manualshive.com logo in svg

Harman Martin Exterior 400, Руководство пользователя

Поделиться
Скачать
Harman Martin Exterior 400 Скачать руководство пользователя страница 3

Safety Information

The following symbols are used to identify important safety information on the product and in this manual:

This product is for professional use only. It is not for household use.

This product presents risks of severe injury or death due to fire hazards, electric shock and falls.

Read this manual

 before installing, powering or servicing the fixture, follow the safety precautions listed 

below and observe all warnings in this manual and printed on the fixture. Install and operate the fixture only 
as described in this manual and in accordance with local laws and regulations. Refer any operation not 
described in this manual to a qualified technician.

If you have questions about how to operate the fixture safely, please contact your Martin supplier or call the 
Martin 24-hour service hotline on +45 8740 0000, or in the USA on 1-888-tech-180.

P R O T E C T I O N   F R O M   E L E C T R I C   S H O C K

• Shut down power to the entire installation at the main power distribution board and lock out power (by 

removing the fuse for example) before carrying out any installation or maintenance work.

• Disconnect the fixture from AC power before removing or installing any cover or part and when not in use. 

• Connect the fixture electrically to ground (earth).

• Use only a source of AC power that complies with local building and electrical codes and has both 

overload and ground-fault (earth-fault) protection. 

• Connect the fixture to AC power either using either the supplied power cable or a listed 3-conductor 

Hypalon or neoprene rubber-jacket cable rated to 90° C (194° F) minimum and with conductor size 1.5 
mm

2

 or 16 AWG minimum.

• Before using the fixture, check that all power distribution equipment and cables are in perfect condition, 

are rated for the current requirements of all connected devices, are protected to IP67 or higher and are of 
suitable type for the location (including water, pollution, temperature and UV resistance).

• Isolate the fixture from power immediately if any cable, seal, cover or other component is damaged, 

cracked or deformed. Do not reapply power until repairs have been completed.

• Do not expose any part of the fixture to a high-pressure water jet.

• Do not immerse the fixture in water or any other fluid, or install it in a location where flooding may occur.

• Refer any service operation not described in this manual to an authorized Martin Service partner.

WARNING!

Read the safety precautions in this section before 

installing, powering, operating or servicing this 

product.

WARNING!

Safety hazard. 

Risk of severe 

injury or death.

WARNING!

Hazardous 

voltage. Risk of 
lethal or severe 

electric shock.

WARNING!

LED light 

emission. Risk 

Group 3 

according to IEC 

62471.

WARNING!

Fire hazard.

WARNING!

Refer to user 

manual.

Содержание Martin Exterior 400









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды