manualshive.com logo in svg

Harman Martin Exterior 400, Руководство пользователя

Поделиться
Скачать
Harman Martin Exterior 400 Скачать руководство пользователя страница 28

 28

Exterior 400 Range user manual

Fuse replacement

DANGER! Lock out power to the entire distribution system before servicing or opening any 
cover. Replace fuses with ones of the same type and rating only.

Primary fuse

Exterior 400 Range fixtures are protected by a 2.5 amp slow-blow primary fuse located on the power PCB. 
If a fixture is completely dead, the primary fuse may have blown. 

To replace the primary fuse:

1. Isolate the fixture from power and allow to cool for 20 minutes.

2. Open the rear cover (see Figure 8 on page 13).

3. Replace a defective fuse with one of the same type and rating only. Replacement primary fuses are 

available from Martin suppliers (P/N 05020010).

4. Reinstall the rear cover as follows:

a. Read“Managing humidity” on page 7.

b. Check that the seal is in perfect condition.

c. Place the seal and cover in position and drive the cover screws until they are finger-tight only.

d. Cross-tighten the screws evenly in a diagonal pattern, increasing torque gradually in stages to a 

maximum torque of 8 Nm (5.9 ft.-lbs.).

5. Reapply power.

Fixture readouts in MUM

Various types of data can be displayed by connecting a PC as described in "

Connecting a PC with MUM"

 on 

page 17 and clicking on the 

Monitor

 button:

Light1

 displays the light level currently measured by light sensor 1 on the back of the fixture.

Voltage

 displays the current voltage in 48 V and 5 V circuits on the main PCB (this data is for service 

purposes).

Temp

 displays the current temperature on the LED circuit board that gives the highest reading, the current 

main PCB temperature and the current ambient temperature.

Fan1

 displays the current cooling fan speed in RPM (revolutions per minute).

Содержание Martin Exterior 400









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды