manualshive.com logo in svg

Harman Martin Exterior 400, Руководство пользователя

Поделиться
Скачать
Harman Martin Exterior 400 Скачать руководство пользователя страница 14

 14

Exterior 400 Range user manual

- If using 

two phases of a three-phase system

 to obtain 

200 - 240 V between two phases, connect one phase to 
terminal 

L

 and the other phase to terminal 

L2

. Do not 

connect anything to terminal 

N

.

- If using 

a single-phase three-wire earthed mid-point 

system

 (used in certain regions of the USA) to obtain 200 - 

240 V between two live conductors, connect one live wire 
to terminal 

L

 and the other live wire to terminal 

L2

. Do not 

connect anything to terminal 

N

.

7. Reinstall the rear cover as follows:

a. Read“Managing humidity” on page 7.

b. Check that the seal is in perfect condition.

c. Place the seal and cover in position and drive the cover 

screws until they are finger-tight only.

d. Cross-tighten the screws evenly in a diagonal pattern, 

increasing torque gradually in stages to a maximum torque 
of 8 Nm (5.9 ft.-lbs.).

8. Screw the new gland into the rear cover until it is tight enough 

to make a seal. Do not overtighten.

9. Tighten the dome nut on the cable gland to grip the cable and 

make a seal before applying power.

Power plug

You may need to fit the supplied power cable with a plug that is suitable for your AC power outlets. If so, 
install a grounding-type (earthed) plug with integral cable grip that is rated 5 A minimum, following the plug 
manufacturer’s instructions. Table 1 on page 12 shows some possible pin identification schemes; if pins are 
not clearly identified, or if you have any doubts about proper installation, consult a qualified electrician. 
Ensure that all connections are sufficiently protected from water. 

L2

L2

N

LL

Figure 10: There is continuity 

between terminals N and L2

Содержание Martin Exterior 400









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды