Harken MKIV Unit 3 страница 6 Скачать руководство пользователя | Manualshive

Страница: 6 / 40

background image

MKIV hydraulic unit 3

6

Preassembly

Rigging Parts Check/Tools/Adhesive

MKIV furlers are shipped with 3M 5200
adhesive. Use adhesives on dry connectors
and foils using the special injection system
described in the assembly section. Parts
may immediately be exposed to rain. Cure
is best at 70° F (22° C) with 50% humidity.
Do not apply at temperatures below 40° F
(5° C) and above 100° F (38° C).

Although adhesive has not cured, it will
remain in place on foil joints whether
they are left on the ground or raised up
on boat. Foils can be raised immediately
after assembly and sails fitted.

Note:

A small amount of adhesive may

bulge out of injection ports. If possible, let
system sit for several days before sailing.
If adhesive gets on sails, remove using
acetone. For faster-curing adhesive, pur-
chase 4200 Fast Cure adhesive sealant.

Note:

Damaged foils can be repaired.

Use a hand-held propane torch to heat
joints until foils can be pulled apart.

Adhesive alert

1. Long tape measure

6. Side cutters

11. Center punch

2. Short tape measure

7. Rat-tail file

12. Rigging or black tape

3. Power drill

8. Hex wrenches (provided)

13. Scissors

4. Drill bit – 5/32" (4 mm)

9. Slotted/Phillips screwdrivers 14. Metal straight edge

5. Hacksaw

10. Needle-nose pliers

15. Hammer

16. Metric ball-end hex wrenches (recommended but not required)

10

13

12

11

8

7

6

5

3

2

1

15

4

14

9

Toggle assembly

1. Harken toggle assembly or hydraulic cylinder required. Sold separately.
2. Mating turnbuckle components with eye at lower end must be purchased

separately. See page 10.
3. Headstay may require cutting and shortening to fit Harken toggle. Some

headstays may remain uncut by replacing lower stud of turnbuckle with

stud/eye, eliminating extra toggle.
4. Rod rigging requires Harken rod adapter stud.

Harken toggle

assembly housing

(sold separately)

Unit

Part no.

3H

7413.25 3/4
7413.25 7/8

16

Rod rigging

Harken rod adapter

stud required

(sold separately)

Unit

Part no.

3H

7426 -22

7427 -30

Hydraulic length-

adjusting cylinder

(sold separately)

Unit

Part no.

3H

7413.26 3/4
7413.26 7/8

WARNING! A stay that is old or damaged may break

suddenly, causing an accident. Headstay condition

should be checked by a professional rigger before reusing.

Hydraulic hoses and adapters

Hoses and adapters are not supplied with furler. See next page for

specifications.

Tools required

«
...
4
5
6
7
8
...
»

Содержание MKIV Unit 3









































Отзывы:

Нет отзывов

Похожие инструкции для MKIV Unit 3

Бренд: Oemtools Страницы: 4

Бренд: Keiser Страницы: 2

Бренд: ECA Страницы: 3

Бренд: Nautilus Страницы: 12

Бренд: B. Braun Страницы: 2

Aesculap Neurosurgery

Бренд: B. Braun Страницы: 13

Aesculap AdTec mini

Бренд: B. Braun Страницы: 2

Бренд: B.Well Страницы: 2

Бренд: B. Braun Страницы: 55

BA Ultimate LED

Бренд: B.A. International Страницы: 234

Бренд: h/p/cosmos Страницы: 81

Бренд: Harken Страницы: 4

Бренд: Harken Страницы: 2

TERRA FORCE BOOM

Бренд: Hardi Страницы: 40

Бренд: Harken Страницы: 4

QuickSlide HemaPRO

Бренд: Hardy Diagnostics Страницы: 2

Бренд: Hardt Страницы: 2

Бренд: unios Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды