Harken MKIV Unit 3 страница 33 Скачать руководство пользователя

Страница: 33 / 40

MKIV hydraulic unit 3

Storage – mast down

In areas where it freezes, do not store system where water can accumulate in foils. Ice will rupture aluminum. Store foils

under cover, with grooves facing down or on an angle so water will run out.

Storage/transporting

Do not store or transport system with lower unit extending beyond mast. Remove lower unit and halyard swivel

for storage and transport.

After storage or transport

After storing or transporting unit, clean thoroughly including tack and halyard swivel ball bearings. See instructions above.

Loosen foil clamp before slacking backstay

In order to prevent foils from locking against upper stay terminal when backstay is released, loosen foil clamp screws

and lower foil before loosening backstay.

Clean and lubricate

Keep unit clean. When you wash boat, flush unit with soap

and fresh water. Occasionally lower sail and flush halyard

swivel with soap and fresh water.
Foils can be cleaned by washing with soap and water.

A scrap of luff tape may be run up foil to scrub inside

grooves. Sail luff tapes may be sprayed with McLube

to reduce friction during sail changes.
Spray sails off boat so McLube

spray does not contact deck.

Maintenance

Clean and Lubricate/Inspect/Storage

Inspect

Inspect unit for signs of chafe, wear or damage.
Inspect clevis and cotter pins below and inside lower unit for

signs of loosening. Check headstay tension for signs of loosening.

Inspect swage fitting and lower toggle for signs of stress corrosion.
Inspect Norseman or Sta-Lok

terminal or rod terminal for

signs of loosening.
Inspect all screws on unit to be sure they have not loosened.
Inspect foil to make sure that it has not dropped into lower unit.

Periodically inspect wire for signs of wear or unraveling.

WARNING! Worn, damaged or corroded parts may

break suddenly. Periodically inspect items listed

below and any others as necessary.

WARNING! Decks sprayed with McLube

will be very slippery which can lead to slipping

and falling overboard. Spray sails off boat so

McLube spray does not contact deck.

McLube is a registered trademark of McGee Industries, Inc.

Sta-Lok is a registered trademark of Sta-Lok Terminals, Ltd.

Содержание MKIV Unit 3









































Результаты поиска

Содержание MKIV Unit 3

Отзывы:

Похожие инструкции для MKIV Unit 3

Бренды по названию

Популярные бренды

Harken MKIV Unit 3, Руководство по установке

Результаты поиска

Содержание MKIV Unit 3

Отзывы:

Похожие инструкции для MKIV Unit 3

Бренды по названию

Популярные бренды