Harken Air 250 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 50

Harken Air 250 Скачать руководство пользователя страница 16

Rev.#0

16

11.

Technical characteristics

Gear ratios and power ratios

Gear

Gear ratio

Power ratio

1

st

1.35

3.44

2

nd

6.40

16.27

3

rd

25.42

64.57

NOTE!
The theoretical power ratio is calculated without taking account of any friction.

NOTE!
For all versions of Winch Air, kits of transmissions are available to modify the gear ratios.
To order the gear kits, contact Harken Italy at

[email protected]

12.

Motorization

Hydraulic equipment (HY)

Hydraulically operated winches have a pull capacity proportional to the working pressure of the system,
while the recovery speed of the winch is proportional to the oil flow.
The hydraulic vertical versions of the Winch Air can be equipped by a hydraulic motor of 200cc
displacement.

Electric equipment (EL)

The electric version of the Winch Air can be equipped by an electric motor powered at 24V, DC,
horizontal mounting.

NOTE!

For the electric connections Winch Air electric powered unit, see the Dual Function Control Box
manual available on Harken website

http://www.harken.it/

For any other information, contact Harken Tech Service at

[email protected]

NOTE!

For motor performances, weights, parts lists and exploded views of the gearmotor assemblies
and other details, contact Harken Tech Service at

[email protected]

«
...
14
15
16
17
18
...
»

Содержание Air 250



















































Отзывы:

Нет отзывов