Network Configuration
39
•
•
•
•
•
•
•
HardcalFailCounts 8: not enough counts between hard cal hi and hard cal lo
•
During a Cal High Command,:Code 2 indicates "calibration in progress".
•
0x66 (102 decimal): C2 CAL CMD
. Write a 0x66 hex to the command register to
perform a C2 calibration.
•
Calibration_Fail 1
•
Calibration_Fail_Motion 3
•
Calibration_Fail_Adc_Error 4
•
Calibration_Fail_Noc2 5
•
Calibration_Fail_C2capeq 6
•
Calibration_Fail_C2clones 7
•
During a C2 Cal Command: Code 2 indicates "calibration in progress".
•
0x1000 (4096 decimal): WRITE INTEGER CMD. Set the value of an integer
parameter. Write 0x1000 in the command register 0, the parameter ID number in
registers 2, 3 and the desired value in registers 4, 5.
• No Error Codes
•
0x1001 (4097 decimal): WRITE FLOAT CMD.
Set the value of a floating point
parameter. Write 0x1001 in the command register 0, the parameter ID number in
registers 2, 3 and the desired float value in registers 4, 5.
•
Failure 1
•
TooHigh -1 : value is above legal limit
•
TooLow -2 : value is below legal limit
•
ErrorNotFound 0x8000 : parameter id not found
Status Word Bits
•
Bit 0 = A/D converter error - bad input from the load cells.
•
Bit 1 = A/D converter failure - no output from the converter to the processor.
•
Bit 5 = Wrong Platform - Trying to load incorrect firmware into unit.
•
Bit 6 = Motion - indicates weight is in motion (changing).
•
Bit 10 = EEPROM Write error - problem writing to the non volatile memory in the unit.
•
Bit 14 = IT test in progress - currently running Integrated Technician test.
•
Bit 15 = Not Found error - Parameter ID not found for command being run.
•
Bits 28-31 = counter - The upper 4 bits are constantly incrementing. This constantly
changing value can be used as confirmation of communications.
Other bits not listed here are not used at this time.
Содержание HI 6500 Series
