HI 2160RC
PLUS
MANUAL
6-26
quate to allow the system plenty of time to stop filling the feeder before the feeder
hopper overflows.
Setting the
START (LO) and
STOP (HI)
Parameters
•
Setting the START (LO) Weight
•
The START (LO) settings are in mass units (actual weight). The
START (LO) begins the Auto Refill Cycle.
Step 1. Press the down arrow
↓
button until the cursor is to the
left of the START (LO) Sub-Menu.
Step 2. Press the Clear button to clear the entry.
Step 3. Use the numeric keys to enter the new value.
Step 4. Press the Enter button to accept the new value.
•
Setting the STOP (HI) Weight.
•
The STOP (HI) settings are in mass units (actual weight).
The STOP (HI) ends the Auto Refill Cycle.
Step 1. Press the down arrow
↓
button until the cursor is to the
left of the STOP (HI) Sub-Menu.
Step 2. Press the Clear button to clear the entry.
Step 3. Use the numeric keys to enter the new value.
Step 4. Press the Enter button to accept the new value.
Setting the LO
SHUTOFF and
HI SHUTOFF
Alarm Weight
Parameters
•
HI and LO SHUTOFF values are entered as absolute weights so
that critical limitations of the process remain firm and fixed.
•
Shutoff levels are utilized to stop a potentially dangerous or expen-
sive error.
•
The setting for LO must be below the START value. The setting for
HI must be above the STOP value.
•
Set the weight value low or high enough to provide a responsive
alarm.
•
When an Alarm condition exists, the “Alarm” relay energizes stop-
ping the feeder and the top line of the operations display reads
**REFILL LO SHUTOFF** or **REFILL HI SHUTOFF**. If an
audio or visual alarm is connected to the controller, that alarm is
energized alerting the operator that an alarm condition exists. For
Remote I/O systems a bit is set and the alarm is indicated on the
display of the PLC or computer.
•
Setting the LO SHUTOFF Weight:
Step 1. Press the down arrow
↓
button until the cursor is to the
left of the LO SHUTOFF Sub-Menu. (See Fig. 6-20)
Содержание HI 2160RC PLUS
