Hardy Barth cPH2 1T11 Скачать руководство пользователя страница 26

Страница: 26 / 28

Standards & Guidelines

The cPH2 charging station complies with the following standards and protection classes:

General standards

Norm

Explanation

2014/30/EU

EMC Directive

2011/65/EU

RoHS Directive

2012/19/EU

WEEE Directive

ElektroG

Electrical and Electronics Act

Standards, protection class and degree of protection for device safety

DIN EN IEC 61851 describes conductive charging systems for electric vehicles:

Norm

Explanation

IEC 61851-1

- General requirements

- Protection against electric shock

- miscellaneous: Environmental conditions

IEC 61851-1, Mode 3

- Charging with specific charging plug-in systems for

electric vehicles with pilot and control contact

IEC 61851-21-2

- Requirements for on-board chargers for electric

vehicles with alternating current / direct current

supply

DIN EN 61851-22

- AC charging station for electric vehicles

Protection class/

protection type

Explanation

Protection class II: The charging station has protective

insulation. No electrically conductive parts on the housing

can be touched.

IP 54

Protection class of the housing:

• complete protection against contact and protected

against dust in harmful quantities

• Protection against splashing water from all sides

Installation and operating manual

cPH2

charging station

Version: 1.0.9

Содержание cPH2 1T11





























Результаты поиска

Содержание cPH2 1T11

Отзывы:

Похожие инструкции для cPH2 1T11

Бренды по названию

Популярные бренды

Hardy Barth cPH2 1T11, Инструкция по установке и эксплуатации

Результаты поиска

Содержание cPH2 1T11

Отзывы:

Похожие инструкции для cPH2 1T11

Бренды по названию

Популярные бренды