Hardi ARROW 2000 Скачать руководство пользователя страница 26

Страница: 26 / 84

3 - Description

Air flow of P540, P540D and HF60 centrifugal blower units

Protective grid

The blower units have protective grids fitted to the air inlets. They are
essential for avoiding accidents and preventing small stones, leaves or
other foreign bodies from entering the blower unit that could cause
damage inside.

€

DANGER! It is strictly forbidden to use the blower unit without the
protective grid.

€

DANGER! Do not approach the fan when in use.

€

DANGER! Do not introduce foreign bodies through the grid,
regardless of whether the turbine is in use or not.

€

DANGER! During the working day, protect your hearing from the
noise produced with EN 352-1:1992 approved earmuffs or similar.

€

DANGER! In the case of vibrations or knocking, stop the turbine immediately.

Blower unit

Speed

Gear ratio

Turbine diameter

Power

Flow

P540

1st low

1 - 5.7

540 mm

25 kW

8000 m3/h

2nd. high

1 - 6.6

540 mm

28 kW

11000 m3/h

Blower unit

Speed

Gear ratio

Turbine diameter

Power

Flow

P540D

1st low

1 - 5.7

540 mm

47 kW

15000 m3/h

2nd. high

1 - 6.6

540 mm

53 kW

19000 m3/h

Blower unit

Speed

Gear ratio

Turbine diameter

Power

Flow

HF540

1st low

1 - 3.6

540 mm

12 kW

8000 m3/h

2nd. high

1 - 4.6

540 mm

16 kW

10000 m3/h

Blower unit

Speed

Gear ratio

Turbine diameter

Power

Flow

HF540D

1st low

1 - 3.6

540 mm

14 kW

11000 m3/h

2nd. high

1 - 4.6

540 mm

22 kW

15000 m3/h

Blower unit

Speed

Gear ratio

Turbine diameter

Power

Flow

HF600D

1st low

1 - 3.5

600 mm

15 kW

19000 m3/h

2nd. high

1 - 4.4

600 mm

20 kW

27000 m3/h

Содержание ARROW 2000





















































































Результаты поиска

Содержание ARROW 2000

Отзывы:

Hardi ARROW 2000, Инструкция, Страница: 26 / 84

Результаты поиска

Содержание ARROW 2000

Отзывы: