Hardi ARROW 2000 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 84

Hardi ARROW 2000 Скачать руководство пользователя страница 20

3 - Description

18

TurboDeflector valve

This TurboDeflector valve activates the Vortex flushing of the
TurboFiller. Lift the lever to lock it in open position for continuous liquid
rotation in the hopper.

Chemical Container Rinsing lever

The upper lever is used for two purposes:

When the TurboFiller lid is open: For rinsing empty containers. Place
the container over the rotating flushing nozzle in the middle of the
TurboFiller to rinse the inside of the container.

When the TurboFiller lid is closed: Use the Chemical Container Rinsing
lever to rinse the hopper when the filling of chemicals is completed.

€

DANGER! Do not press the lever unless the multi-hole nozzle is covered by a container as spray liquid may otherwise
hit the operator.

Rinse tank

The rinse tank is coaxially coupled inside the 2000, 3000 and 3800 litre
tanks.

This tank is completely separate and is not connected with the main
tank.

±

WARNING! The tank should only be filled with clean water and a
disinfectant agent, and it should only be used for rinsing and
cleaning the equipment inside and out.

Start TurboDeflector

Chemical Container Rinsing

«
...
18
19
20
21
22
...
»

Содержание ARROW 2000





















































































Отзывы:

Нет отзывов