Hardi ARROW 2000 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 84

Hardi ARROW 2000 Скачать руководство пользователя страница 17

3 - Description

15

Pressure manifold

This steel part is located at the front of the machine, beside the control
unit. Agitation, tank flushing (according to model) and the powder
mixer are activated from this manifold using the ball check valves.

It also includes a free ball check valve for connecting the spray gun and
the safety valve of the pressure circuit.

Operating unit

The mistblower can be fitted with different models of operating units:

BKC/2 or EVC/2 for low pressure

The low-pressure operating units are used with the HLC circuit.

MC/2 operating unit

This manual operating unit contains two levers with a long-distance cable for individually opening the spray zones from the
tractor cabin. The pump includes a manual valve for raising or lowering the pressure and a pressure gauge.

SV/2 operating unit

This high-pressure electric operating unit contains a manual pressure valve fitted to the machine and a electric control box
for opening and closing the section valves from the tractor cabin.

«
...
15
16
17
18
19
...
»

Содержание ARROW 2000





















































































Отзывы:

Нет отзывов