Harbor Freight Tools BADLAND APEX 12000 страница 15 Скачать руководство пользователя

Страница: 15 / 20

Page 15

For technical questions, please call 1-888-866-5797.

56385

SAF

Ten

Troubleshooting

Problem

Possible Causes

Likely Solutions

Motor

overheats.

1.  Incorrect power cords.
2.  Winch running time too long.
3.  Insufficient current or voltage.

4. Loose motor connections.

1.  Use only supplied power cords.
2.  Allow Winch to cool down periodically.
3.  Fully charge battery. Run Winch

with vehicle motor running.

4. Check and tighten motor connections to Control Box.

Motor does

not turn on.

1. Remote Socket not

connected properly.

2. Loose battery cable connections.
3. Insufficient current or voltage.

4. Defective contactor.
5. Wireless Receiver

Switch turned OFF.

6. Wireless Remote turned OFF.
7. Winch Disconnect

Switch turned OFF.

8. Low batteries in Wireless Remote.
9. Defective motor.

10. Loose Control Box ground cable.
11. Internal wear or damage.

1. Insert Remote Socket all the way into connector.

2. Tighten nuts on all cable connections.
3. Fully charge battery. Run Winch

with vehicle motor running.

4. Replace Control Box.
5. Turn ON Wireless Receiver Switch.

6. Turn ON Wireless Remote.
7. Turn ON Winch Disconnect Switch.

8. Replace Remote batteries —CR2450, quantity one.
9. Check for voltage at armature port with Switch

pressed. If voltage is present, replace motor.

10. Check and tighten ground cable to Control Box.
11. Replace motor.

Motor runs

but drum does

not turn.

Clutch not engaged.

Move the Clutch Handle to the Engaged position.

If problem persists, a qualified technician

needs to check and repair.

Motor runs

slowly or

without normal

power.

1. Insufficient current or voltage.

2. Loose or corroded battery

cable connections.

3. Incorrect power cords.

1. Battery weak, recharge.

Run Winch with vehicle motor running.

2. Clean, tighten, or replace.

3. Use only supplied power cords.

Motor runs in

one direction

only.

1.  Defective contactor.
2.  Defective Wireless Remote.
3.  Loose motor connections.

1.  Replace Control Box.
2.  Replace Wireless Remote.
3.  Check and tighten motor connections to Control Box.

Follow all safety precautions whenever diagnosing or servicing

the tool. Disconnect power supply before service.

Содержание BADLAND APEX 12000





















Результаты поиска

Содержание BADLAND APEX 12000

Отзывы:

Похожие инструкции для BADLAND APEX 12000

Бренды по названию

Популярные бренды

Harbor Freight Tools BADLAND APEX 12000, Руководство пользователя и инструкции по безопасности

Результаты поиска

Содержание BADLAND APEX 12000

Отзывы:

Похожие инструкции для BADLAND APEX 12000

Бренды по названию

Популярные бренды