background image

OPERATING INSTRUCTIONS

17

16

TROUBLESHOOTING

CARE AND MAINTENANCE

•  To reduce the risk of fire, electric shock or injury to persons, care and maintain this fan.

•  Important:

 Shut off main power supply before beginning any maintenance.

•  Do not use water or detergents when cleaning the fan or fan blades. A dry dust cloth or 

lightly dampened cloth will be suitable for most cleaning.

•  Clean fan housing with only a soft brush or lint-free cloth to avoid scratching the finish. 

Clean blades with a lint-free cloth. You may occasionally apply a light coat of furniture 

polish to blades for added protection.

•  At least twice a year, tighten all screws and lower canopy to check mounting bracket 

screws and downrod assembly.

 

PROBLEM

POSSIBLE CAUSE

CORRECTIVE ACTION

Fan does not move.

1.  Chain switch is “off”.

2.  Faulty wire 

connection.

3.  Reverse switch not 

engaged.

1.  Pull chain switch.

2.  Turn power off. Loosen 

canopy, check all connections.

3.  Push switch firmly either way.

Noisy operation.

1.  Blades are loose.

2.  Cracked blade.

3.  Unapproved speed 

control.

1.  Tighten all blade screws.

2.  Replace blades (call customer 

service).

3.  Replace with an approved 

speed control device.

Excessive wobbling. 1.  The blades are loose.

2.  Blade brackets 

incorrectly attached.

3.  The fan is not 

securely mounted.

4.  Fan too close to 

vaulted ceiling.

1.  Tighten all blade screws.

2.  Reinstall blade brackets.

3.  Turn power off. Carefully 

loosen the canopy and 

remount securely.

4.  Lower fan or move it to 

another location.

1.  The fan pull chain is for motor speed control: High, Medium, Low and Off. Pull the chain 

once for each position.

2.  The light pull chain controls the light fixture either ON or OFF with each pull of the chain.

PULL CHAIN: 

REVERSE SWITCH:

When the season changes ,you may want to change the direction the fan blades spin. To 

switch between clockwise and counterclockwise rotation, flip the fan reversal switch. 

NOTE

: Wait for fan to stop before reversing switch.

A. In cooler weather, clockwise rotation 

creates an upward airflow, which 

moves hot air from the ceiling into the 

room. Push the switch UP and see a 

Snowflake icon.

B. In warmer weather, counterclockwise 

rotation creates downward airflow, 

which cools the air. Push the switch 

DOWN and see a Sun icon

Snowflake

icon

Sun

icon

Содержание 00892





















Отзывы: