Snapper
6 Micro FPV Racing Drone FRSKY BNF Version
Binding procedure
Arm/Disarm the Motor
1. The Default Arm/Disarm switch for
is AUX1(Channel 5),and you can also customize it
Snapper
6
with Betaflight Configurator.
VTX Bands and Channels setup
Frequency
switching
:
By
one
button
,
Short
press
the
button
to
change
channel
,
1
-
8
adjustable
.
Press
and
hold
the
button
for
2s
to
change
bands
,
1
-
6
adjustable
.
Two
groups
of
LEDs
:
Group
1
:
6
BLUE
LED
stand
for
bands
Group
2
:
8
RED
LED
stand
for
channels
Blue
LED1
and
Red
LED1
light
on
,
indicating
frequency
5865MHZ
(
BAND1
and
CH1
)
Blue
LED1
and
Red
LED2
light
on
,
indicating
frequency
5845MHZ
(
BAND1
and
CH2
)
Blue
LED6
and
Red
LED8
light
on
,
indicating
frequency
5600MHZ
(
BAND6
and
CH8
)
Frequency
and
channel
frequency
table
:
Blue
LED
1
Blue
LED
6
Red
LED
8
Red
LED
1
Video
In
Video
Out
GND
3.3-5.5V
Specifications
Features
Betaflight support , multi flight mode: ACRO/AIR/ANGLE
Powerful Brushless motor and Smooth ESC
CNC aluminum alloy propeller guard
Betaflight OSD support ,easy to get RSSI , Voltage and other info from your goggles
Frsky version support both EU LBT and NON-EU Frsky transmitter
Head lights ready
Camera angle adjustable
1. Power for the Snapper
6 and the LED Combo(2 red led and 2 white LED) will blinking slowly,
then Press and hold the bind button for 2 seconds, the LED Combo(2 red led and 2 white led)
will getting to be solid, this indicate the Snapper
6 Quadcopter is in binding mode
2. Turn on your Frsky Taranis transmitter, and move to BIND OPTION from SETUP MENU,
Choose receiver mode D16 or D8 according to your Betaflight receiver configuration
(Frsky_X = D16 mode, Frsky_D=D8 mode)
3
.
ENT [Bind] to binding with the Snapper
6, the LED Combo(2 red led and 2 white led) will
blinking slowly on the flight controller ,this indicate binding successfully, and then exist
binding mode of your Frsky transmitter, the LED Combo(2 red led and 2 white led) will getting
to be solid again, this indicate working normal.
3
.
The default channel map for Snapper
6 Frsky version is TAER1234, please make sure your
transmitter is matched, otherwise it will can't be armed. Toggle the AUX1 Switch ,the Green
LED on the flight controller will getting to be solid, this indicates the motor was armed . And
also you can found “Armed” displayed on your FPV Goggles or the FPV Monitor. Please make
sure keep the Snapper
6 level before arming .Be careful and enjoy your flight now !
Toggle the AUX1 Switch, the Green LED on
the Flight controller will getting to be solid
Toggle the AUX1 Switch, the Green LED on
the Flight controller will getting to be solid
Receiver configuration
Please set Receiver mode to be SPI RX Support from the Configuration tab of the Betaflight
Configurator, then select FRSKY_X Provider for FRSKY D16 MODE or Select FRSKY_D Provider
for FRSKY D8 MODE, don't enable Serial RX since the CRAZYBEE Flight controller is integrated
SPI BUS Receiver
2.Turn on the Frsky transmitter (Use X9D+ as an example) and move to the MIXER interface,
Set “SA” or “SB” switch etc. for Ch5 to ARM/DISARM the motor
.
Notes:
1.The receiver signal will be unstable while the MSP(Connect to Betaflight) Connection established
2.The PID loop frequency must be 2kHZ at this firmware version, will update soon .
Brand Name: Happymodel
Mode Name: Snapper6
Item Name: 1S Brushless Whoop racer drone BNF
Wheelbase: 65mm
Size: 81mm*81mm*36mm
Weight: 23g(without battery)
1
1
4
1
1
1
1
0
1
1
Components
Basic Version
1
1
4
1
1
3
0
1
1
1
Standard Version
SP601
SP602FR
SP603
SP604
SP605
SP606
SP607
SP608
SP609
SP610
Part. NO.
Snapper 6 Frame
Crazybee F3 Flight controller Frsky
SE0603 KV19000 Motor 0.8mm shaft
31mm 3-blades propeller(4cw+4ccw)
AIO Camera & VTX
3.8v 250mah 30C/60C battery
USB Lipo/LIHV Charger
1S06 6 way Lipo/LIHV charger
Propeller disassemble tool
Screwdriver
