3
MK0101KE180920
Danger
Warning
Caution
Analog Temperature Controller
HY-4500/4700/5000
Thank you for purchasing HANYOUNG product.
Please check whether the product is the exactly same as you ordered.
Before using the product, please read this instruction manual carefully.
Please keep this manual where you can view at any time
INSTRUCTION MANUAL
1381-3, Juan-Dong, Nam-Gu Incheon, Korea.
TEL:(82-32)876-4697 FAX:(82-32)876-4696 http://www.hynux.net
HANYOUNGNUX CO.,LTD
HEAD OFFICE
Safety information
Before using the product, please read the safety information thoroughly and use it properly.Alerts
declared in the manual are classified to Danger, Warning and Caution by their criticality
There is a danger of occurring electric shock in the input/output terminals so please never let
your body or conductive substance is touched.
•If there is a concern about a serious accident caused by a malfunction or abnormality of this
product, please install an external protection circuit and devise a scheme for preventing an accident.
•This product does not contain an electric switch or fuse, so the user needs to install a
separate electric switch or fuse externally. (Fuse rating: 250 V 0.5 A)
•To prevent defection or malfunction of this product, apply a proper power voltage in
accordance with the rating.
•To prevent electric shock or malfunction of product, do not supply the power until the wiring is completed.
•Since this product is not designed with explosion-protective structure, do not use it any place
with flammable or explosive gas.
•Do not decompose, modify, revise or repair this product. This may be a cause of malfunction,
electric shock or fire.
•Reassemble this product while the power is OFF. Otherwise, it may be a cause of malfunction or electric shock.
•If you use the product with methods other than specified by the manufacturer, there may be
bodily injuries or property damages.
•There is a possibility of occurring electric shock so please use this product after installing it
onto a panel while it is operating.
•The contents of this manual may be changed without prior notification.
•Before using the product you purchased, make sure that it is exactly what you ordered.
•Make sure that there is no damage or abnormality of the product during the delivery.
•Use this product within the range of the operating ambient temperature, 0 ~ 50 ℃ (When it is
closely installed Max 40 ℃) and ambient humidity, 35 ~ 85 % R.H (No condensation).
•Do not use this product at any place with occurring corrosive
(especially noxious gas or ammonia) or flammable gas.
•Do not use this product at any place with direct vibration or impact.
•Do not use this product at any place with liquid, oil, medical substances, dust, salt or iron
contents.(Use at Pollution level 1 or 2)
•Do not polish this product with substances such as alcohol or benzene. (Use neutral detergent.)
•Do not use this product at any place with a large inductive difficulty or occurring static
electricity or magnetic noise.
•Do not use this product at any place with possible thermal accumulation due to direct sunlight or heat radiation.
•Install this product at place under 2,000m in altitude.
•When the product gets wet, the inspection is essential because there is danger of an electric leakage or fire.
•In case of inputting thermocouple, use a compensating cable.
(If using a normal wire, there is a possibility of occurring temperature error.)
•For R.T.D input, use a cable which is a lead wire has small resistance and resistances of three wires
shall be the same. (If the three wires have different resistances then there will be a temperature error.)
•To avoid an effect of inductive noise to input signal cables, use the product after separating
the input signal cables from power, output and load cables.
•Separate an input signal cable from an output signal cable. If separating is not possible,
please use the input signal cable after shielding it.
•Use non-earth sensor with thermocouple. (In case of using earth sensor, there is a possibility
of occurring malfunction caused by a short circuit.)
•If there is excessive noise from the power supply, using insulating transformer and noise filter is
recommended. The noise filter must be attached to a panel which is already connected to a ground
and the wire between the filter output side and power supply terminal must be short as possible.
•If twisting the power cables closely together then it is effective against noise.
•If the alarm functions are not properly set then it will not be output when the product is
malfunctioning. Therefore, make sure its movements are properly working before the operation.
•Turn the power OFF when replacing a sensor.
•Use an auxiliary relay in case of high frequent operation such as proportional operation or etc.
its life span will be shorter if connecting a load without permissible rating of output relay. In this
case, using SSR output type is recommended.
·Life Span of Contact Point Output :
Mechanical Life Span: above 10 million times (with no load)
Electrical Life Span: 100 thousand times (250 V a.c 3 A: with the rated load)
•Do not connect anything to the unused terminals.
•After checking the polarity of terminal, connect wires at the correct position.
•When this product is connected onto a panel, use a circuit breaker or switch approved with IEC60947-1 or IEC60947-3.
•Install a circuit breaker or switch at near place for convenient use.
•Write down on a label that if the circuit breaker or switch is operating then the power will be
disconnected since the circuit breaker or switch is installed.
DANGER
DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury
WARNING
WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury
CAUTION
CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury
Suffix code
•For the continuous and safe use of this product, the periodical maintenance is recommended.
•Some parts of this product have limited life span, and others are changed by their usage.
•The warranty period for this product including parts is one year if this product is properly used.
•When the power is on, the preparation period of contact output is required. In case of using
signals of external interlock circuit or etc., use it with a delay relay.
•In case of replacing this unit with a spare unit, make sure its compatibility because its operation
can be different by different parameter settings even though the model name is the same.
•Before using a temperature controller, there could be a temperature difference between PV of
the temperature controller and the actual temperature so please operate the temperature
controller after compensating the temperature difference appropriately.
Range and Input code chart
Dimension and Panel cutout
█ HY-5000
[Unit : mm]
Model
Code
Description
HY-
Analog indication temperature controller
Dimension
4500S
96(W) × 96(H)
4700S
96(W) × 96(H) (Auxiliary output : L.M)
5000S
72(W) × 72(H)
Control type
F
ON/OFF control (2 position control)
P
Proportional control
Input
K
K thermocouple
J
J thermocouple
R
R thermocouple
P
RTD Pt100 Ω(IEC)
V
1 - 5 V d.c
C
4 - 20 mA d.c
Control output
M
Relay
C
Current output (4 - 20 mA d.c)
S
S.S.R (12 V d.c Voltage pulse output)
Sub output (L.M)
(Apply only with the model
HY-4700)
N
None
O
High action
P
Low action
W
High·Low action
Control operation
R
Reverse action (Heating control)
D
Direct action (Cooling control)
Range code
Select the standard range code
Model
Code No
HY-4500S, HY-4700S
HY-5000
Input
Range (℃)
Input
Range (℃)
1
Pt100 Ω
-50 ~ 50
Pt100 Ω
-50 ~ 50
3
Pt100 Ω
-50 ~ 100
Pt100 Ω
0 ~ 100
5
Pt100 Ω
0 ~ 100
K, Pt100 Ω
0 ~ 200
6
-
-
K, Pt100 Ω
0 ~ 300
7
K, Pt100 Ω
0 ~ 200
K, Pt100 Ω
0 ~ 400
8
K, Pt100 Ω
0 ~ 300
K
0 ~ 600
9
K, J, Pt100 Ω
0 ~ 400
K
0 ~ 800
10
K
0 ~ 600
K
0 ~ 1200
11
K
0 ~ 800
-
-
13
K
0 ~ 1200
-
-
14
R
0 ~ 1600
-
-
INDONESIA
FACTORY
JL.CEMPAKA BLOK F 16 NO.02 DELTA SILICON II INDUSTRIAL PARK
LIPPO CIKARANG CICAU, CIKARANG PUSAT BEKASI 17550 INDONESIA
TEL : 62-21-8911-8120~4 FAX : 62-21-8911-8126
PT. HANYOUNG ELECTRONIC INDONESIA
