5
English
Safety Notes
Gloves should be worn during installation to prevent
crushing and cutting injuries.
Intended Use
The product may only be installed and connected
outside areas 0, 1 and 2 following the
manufacturer’s specifications.
The circuit must be protected via a ground fault
protector (RCD / FI) with a measured differential
current of ≤ 30 mA.
A different or excessive use is considered non-
intended. The user/operator bears the sole risk.
Please contact your contracting party to claim your
rights under this guarantee. This guarantee does not
affect the customer's rights under the respective
national legislation.
The manufacturer/seller of this light does not assume
any responsibility for injuries or damage that may be
caused by improper installation or non-intended use.
The light source of this luminaire is not replaceable;
when the light sources reaches its end of life, the
whole luminaire must be replaced.
Electrical installation
Electrician
Installation and tests are to be performed by an
approved electrician, taking VDE 0100, Part
701 into account. It's a Legal Requirement for the
Installation and wiring to conform to current IEE
Electrical and Building regulations.
Electrical connection
Voltage supply:
100 - 240V/N/PE/50 - 60Hz
Residual current protection system
The circuit must be protected via a ground fault
protector (RCD / FI) with a measured differential
current of ≤ 30 mA.
The proper function of this protective device must be
checked at regular intervals.
Installation Instructions
• Prior to installation, inspect the product for transport
damages. After it has been installed, no transport or
surface damage will be honoured.
• The plumbing codes applicable in the respective
countries must be observed.
• Any work may only be carried out in a de-energized
state. Here, the voltage supply must be safely
separated via the main switch or mains plugs.
• Only standardized materials may be used for the
installation.
• All components must remain accessible.
• The ambient temperature must not exceed 40 ºC.
• During operation this lamp will get hot. A minimum
distance of 50cm should be maintained, away from
inflammable items.
• During installation of the product by qualified trained
personnel, make sure that the entire fastening surface
is even and smooth (no protruding seams or tile
offset), that the finish of the wall is suitable to apply
the product and has no weak points.
Technical Data
Nominal voltage:
100 - 240V/N/PE/50 - 60Hz
Power:
max. 2,5 W
Protection class:
IP 20
Serial number
see typeplate
Dimensions
see page 47
weight:
1.380g
Symbol description
Read the installation instructions
Beware of dangerous electrical
current
Do not use silicone containing acetic acid!
Dimensions
(see page 47)
Cleaning
(see page 48)
• Switch off light.
• Remove marks (cremes, cosmetics etc.) with a
chamois leather that has been rinsed in hot water
and wrung out well. Always wipe around the edges
with a clean, dry cloth. Do not use glass or window
cleaner or other chemicals, as these may damage
the silver coating and cause brown marks. We
cannot accept liability or provide guarantee cover if
these instructions are ignored.
• Wipe surface with a soft dry or damp cloth.
• Ensure no moisture or fluid into the light.
• Damage caused by using incorrect cleaners or
misuse is not covered by our guarantee.
Содержание 73570000
