background image

1.2    Use occasions and conditions 

The forklifts described in this manual are only suitable for loading and unloading and transporting 

goods over short distances. 

It must be used, operated and maintained according to the information in this manual. Any other 

uses are outside the design envelope and can lead to injury to persons or damage to equipment or 

property. 

Only used in specified place and condition

 

 

Use in specified rated load. 

 

Used in specified area as factory, tourist attraction and recreation place. 

 

Used on the flat ground, that is fixed and owns enough carrying capacity. 

 

Used on the road with good vision and equipment use license. 

 

Approved working site temperature is -5

℃~

40

.   

 

Altitude should not over 2000m. 

 

Max. gradability when driving with full load is 18%. It is prohibited to travel crosswise or 

obliquely when going uphill. When going uphill with loads, keep the loads in front; when 

going downhill, keep people in front.       

Please read other safety rules in this manual, it is important to your personal safety, working staff 

and goods safety. 

  Warning

 

 

It is forbidden to drive outside the designated areas such as highways. 

 

Overloading and illegally carrying people are strictly prohibited. 

 

Do not push or pull loads. 

 

Non-explosion-proof forklifts are forbidden to be used in flammable and explosive places. 

 

If it is not a cold storage type, it is forbidden to use it in a cold storage. 

 

 

 

 

 

 

Содержание XC Series
































































































Отзывы: