Hangar 9 Cap232 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 44

Hangar 9 Cap232 Скачать руководство пользователя страница 17

17

Section 6: Installing the Rudder and Elevator Servos

Fuselage

Not included

Servos (4) (a minimum of 80 oz/in of torque)

w/mounting hardware

Small cable ties (2)

Using a computer radio

24" Servo Extensions (4) (JRPA102)

Using a non-computer radio

Y-Harnesses (3) (JRPA133)
18" Servo Extensions (4) (JRPA099)

Note:

If using a non-computer radio, one of the servos used

for elevator must be a reversed-direction servo. See the
"Radio Setup" section for more details on page 34.

Included in optional Hangar 9

™

Hardware Kit

1" Heavy-Duty Servo Arms for Elevator (2)

(HAN3574-JR or HAN3575-Futaba)

1

1

/

4

" Heavy-Duty Servo Arms for Rudder (2)

(HAN3578-JR or HAN 3579-Futaba)

4

1

/

2

" 4-40 Linkages (4) (HAN3556)

4-40 Ball Links (4) (ROC87)
Swivel Control Horns (2) (ROC01B)

Phillips screwdriver
Small straight screwdriver

Parts Needed

The rudder and elevators require a minimum of 80 in/oz of servo
torque. In the prototype 1/3 Scale CAP 232, we used JR8101 and
JR8411 servos with excellent results. Using servos with less
torque could cause a crash.

Computer Radio

Step 1.

If using a 7-channel or greater computer radio with

mixing (highly recommended), install four 24" servo extensions,
one on each servo. Tie a knot at each connector and tape to
prevent inadvertent disconnection. Also install the servo
hardware (grommets and eyelets) at this time.

Non-Computer Radio

Step 1a.

If using a non-computer radio, install four 18" servo

extensions, one on each servo. Tape and tie a knot at each
connector to prevent inadvertent disconnection. Install one side
only of the two Y-harnesses to two of the servos, also tying knots
to prevent disconnection. The other two servos will be hooked up
to the Y-harness when installed in the airplane. One elevator
servo will need to be a reversed-direction servo.

Tools and Adhesives Needed

«
...
15
16
17
18
19
...
»

Содержание Cap232













































Отзывы:

Нет отзывов