![HandHeld Dolphin 7850 Series Скачать руководство пользователя страница 27](http://html1.mh-extra.com/html/handheld/dolphin-7850-series/dolphin-7850-series_user-manual_589826027.webp)
Dolphin® 7850 Series User’s Guide–
Preliminary
3 - 13
Resetting the Terminal
There are two ways to reset the Dolphin terminal: a soft reset and a hard reset.
Soft Reset (Warm Boot)
A soft reset re-boots the device without losing RAM data. You would perform a soft reset 1) when the terminal fails to respond,
2) after installing software applications that require a reboot, or 3) after making changes to certain system settings.
1. Press and hold the Red
+ ESC
keys for approximately five seconds. The screen turns white and the decode and
scan LEDs flash for approximately three seconds.
2. When the reset is complete, the Today screen appears.
Hard Reset (Cold Boot)
A hard reset erases all of the data and applications stored in RAM memory and launches Autoinstall, which re-initializes the
terminal.
1. Press and hold the Red
+ Tab
keys for approximately five seconds. The screen turns white and the decode and
scan LEDs light for approximately three seconds.
2. The terminal re-initializes; see
Note: Hard resets automatically launch a soft reset before ending on the Today screen.
Set the time and date after each hard reset to ensure that the system clock is real-time. Tap the date on the Today screen to
open the Clock and set the time and date.
Suspend Mode
Suspend mode suspends terminal operation. The terminal appears to be “off” when in suspend mode.
The terminal is programmed to go into suspend mode automatically when inactive for a specific period of time. You can set this
time period in the Power setting. For details, see the
Advanced Tab
section of the
To Put the Terminal in Suspend Mode
Press the Blue
+ Backlight
keys. You should put the terminal in suspend mode when you change the battery pack;
Installing the Main Battery Pack
To Resume Terminal Operation
To resume terminal operation (or “wake” the terminal),
•
Press the Backlight key
.
•
Press the
Troubleshooting
If the terminal does not wake when you press the scan trigger,
•
The battery door may not be fully closed. The mechanical switch under the battery door prevents the terminal from resuming
operation until the door is closed.
•
The main battery might be too low to resume operation. Remove the battery and install a fully charged battery or connect the
terminal to a Dolphin charging peripheral.
!
Содержание Dolphin 7850 Series
