Hamworthy VARMAX 120 Скачать руководство пользователя страница 27

Страница: 27 / 156

14.09.2020

27 / 156

VARMAX -

Installation, Use and Maintenance

INFORMATION:

The lengths of the ducts provided below are in linear metres (lm). The total

length of all ducts is reduced to a straight length (elbows having a straight

equivalence).

4.10.3.

On VARMAX 180 and 22

The type of gas is changed by replacing the

diaphragm located on the gas line.

Unscrew the 4 nuts (see opposite), then remove

the diaphragm in place (brass part).

Replace this with that provided with the boiler

(engraved B2P).

Screw the 4 nuts back in place.

Check the CO

settings (see §

7.7, page 52

After changing the type of gas:

- Check the sealing of the gas line.

- Stick the label provided in place of the

original label (G20).

Note:

In order to facilitate the operation, the mounting

flange located at the entrance to the gas line (on

the side nearest the network connection) may

require unscrewing.

4.11. Exhaust connection

Exhaust system works and national and prefectoral regulations must be

complied with.
A smoke temperature sensor guarantees the protection of exhaust ducts for

type B and C combustion products.

VARMAX boilers are approved to be connected to:

• a B23 chimney (all models)

• a B23P chimney (all models)

• a C13 air vent (models 120 to 225) except for propane gas (G31)

• a C33 air vent (models 120 to 225) except for propane gas (G31)

• a C53 air vent (all models) except for propane gas (G31)

4.11.1.

Connection to a B23 chimney

Type B23 connection:

Air from the unit's premises, extraction of gases through the roof via a flue

with natural ventilation.

WARNING:

Check that there are top and bottom ventilations in the boiler premises,

that they comply with applicable regulations and that they are not

obstructed.

figure 18 -

Diaphragm

B2P

Diaphragm

orientation

engraving

towards the

gas valve

nut (x4)

Содержание VARMAX 120





























































































































































Результаты поиска

Содержание VARMAX 120

Отзывы:

Похожие инструкции для VARMAX 120

Бренды по названию

Популярные бренды

Hamworthy VARMAX 120, Инструкция по установке, наладке и обслуживанию

Результаты поиска

Содержание VARMAX 120

Отзывы:

Похожие инструкции для VARMAX 120

Бренды по названию

Популярные бренды