Hamworthy STRATTON MK3 Series Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 154

background image

6 / 154

STRATTON MK3 - Installation, Use and Maintenance

00U07428680-C

1.4. Safety instructions

Current Gas Safety (Installation and Use) Regulations or rules in force.
The appliance is suitable only for installation in GB and IE and should be

installed in accordance with the rules in force.
In GB, the installation must be carried out by a suitably qualified Gas Safe

registered engineer or in IE by a competent person. It must be carried out in

accordance with the relevant requirements of the:
• Gas Safety (Installation and Use) Regulations
• The appropriate Building Regulations either The Building Regulations, The

Building Regulations (Scotland), Building Regulations (Northern Ireland).

• The Water Fittings Regulations or Water byelaws in Scotland.
• The Current I.E.T. Wiring Regulations.

Where no specific instructions are given, reference should be made to the

relevant British Standard Code of Practice.
In IE, the installation must be carried out by a Competent Person and installed

in accordance with the current edition of I.S.813 “Domestic Gas Installations”

or I.S. 820 “Non-Domestic Gas Installations” as appropriate, the current

Building Regulations and reference should be made to the current ETCI

rules for electrical installation.
The Boiler boilers have been tested and certified to;
BS EN 15502-1, BS EN 15502-2, BS EN 15502-2-1, BS EN 60335-1,
BS EN 60335-2-102, BS EN 55014-1 and BS EN 55014-2 for use with Natural

Gas & Propane.
Detailed recommendations are contained in the following Codes of Practice:
BSEN 60529 IPX4D using test method: Figure 4 - Test device to verify

protection against spraying and splashing water; second characteristic

numerals 3 and 4 (oscillating tube).
BS. 6891 Installation of low pressure gas pipework of up to 28mm (R1) in

domestic premises (2nd family gas).
BS. 5440 Inst. and maintenance of flues and ventilation for gas appliances of

rated input not exceeding 70kW net (1st, 2nd and 3rd family gases).
Part 1 Specification for installation of flues.
Part 2 Specification for installation and maintenance of ventilation for gas

appliances.

BS. 6644 : 2011 Installation of gas fired hot water boilers of rated inputs

between 70kW and 1.8MW (net) (2nd and 3rd family gases).
BS. 6798 Installation and maintenance of gas fired hot water boilers of rated

input not exceeding 70kW net.
BS. 6880 Low temperature hot water heating systems of output greater than

45kW.
Part 1 Fundamental and design considerations.
Part 2 Selection of equipment.
Part 3 Installation, commissioning and maintenance.
BSEN.12828:2012 Heating Systems in buildings: Design for water based

systems.

«
...
4
5
6
7
8
...
»

Содержание STRATTON MK3 Series



























































































































































Отзывы:

Нет отзывов

Похожие инструкции для STRATTON MK3 Series

Бренд: Warmhaus Страницы: 48

Бренд: Easylife Страницы: 4

Бренд: Lamborghini Caloreclima Страницы: 44

Бренд: Bakers Pride Страницы: 24

ITACA CH KR 105

Бренд: Fondital Страницы: 104

Бренд: Immergas Страницы: 16

Бренд: Beretta Страницы: 144

Бренд: Baxi Страницы: 36

VOGUE MAX COMBI 40IE

Бренд: Ideal Heating Страницы: 24

Бренд: Lamborghini Caloreclima Страницы: 188

Бренд: Kiturami Страницы: 20

Бренд: Stanley Страницы: 28

recoVAIR VAR 260/4

Бренд: Vaillant Страницы: 16

ecoTEC plus SERIES

Бренд: Vaillant Страницы: 44

Бренд: Vaillant Страницы: 40

ecoTEC exclusive

Бренд: Vaillant Страницы: 52

Бренд: Vaillant Страницы: 80

ecoTEC exclusive 627

Бренд: Vaillant Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды