background image

Assembly of the Light Fixture:  Option 1 - Hidden wire

 

Find a location on the deck where you want to mount the light.

 

Using the template provided with the instruction manual, place it 

over the deck and use a sharp object or a pen to mark where you 

are going to put the screws (E) and drill the hole. 

 

Drill a 1 in. hole where specified. Use the two (2) provided screws 

(E) and screw them in the deck according to the template.

 

Pass the wire (C) and the connector (D) through the hole.

 

Mount the half brick light (B) on the screws (E).

Assembly of the Light Fixture: Option 2 – Flushmount

 

Find a location on the deck where you want to mount the light.

 

Using the template provided with the instruction manual, place it 

over the deck and use a sharp object or a pen to mark where you 

are going to put the screws (E).

 

Insert the screws (E).

 

Mount the half brick light (B) on the screws (E).

Assembly of the Light Fixture: Option 3 – Flushmount to cover older models

 

Remove the diffuser plate and the light component by unscrewing 

the two thumbscrews (B)

 

Pass the wire in the hole

 

Secure the fixture onto the surface, covering the hole from the old 

light fixture using the two screws from the old model (not included)

 

Install the diffuser and light component with the two thumbscrews (B)

 

Make sure the O-ring stays on the thumbscrews (B)

Item #1001 492 878 

Model #HD38682

Use and Care Guide 

LOW VOLTAGE LED HALF BRICK STEP LIGHT

Part

Description

Quantity

A

Thumbscrews

2

B

Half brick light assembly

1

C

Wire

1

D

Connector

1

E

Screws

2

PACKAGE CONTENTS

Assembly and Installation

1

 

Attaching and installing the light

2

 

Connecting the wires

WARNING: The wire connector (D) contacts have sharp edges for piercing the 
main low voltage cable. To avoid injury, do not touch the metal contacts.

CAUTION: The wire from the low voltage power unit shall be 12-16 AWG type 
underground low Energy Circuit Cable or SPT2W.

IMPORTANT:  
•  Protect the wiring by routing it in close proximity to the light fitting, or next to a  
  building structure such as a house or deck. 
•  The landscape wire and connector can also be hidden under stone or buried  
  under grass at a maximum depth of 6” (15.24 cm). 
•  Do not submerge fixture in water.

WARNING: Risk of Electric Shock. Install all luminaires 10 ft. (3.05 m) or more 
from a pool, spa or fountain.

 

Place the wire connector (D) on opposite sides of the low 
voltage cable (not included) where the fixture will be located.

 

Align and fit the main low voltage cable vertically to the slot of 
the wire connector (D) as shown.

 

Press the wire connector (D) together until fully seated and 
locked around the cable. Pre-set prongs will pierce the cable 
insulation and establish contact. Turn on the power unit. If the 
light fixture does not turn on, repeat the previous steps.

 

Once the clip-on connector (D) is in place, wrap it with 
electrical tape for additional protection. 

 

CAUTION BE CAREFUL! THE WIRE STABS ARE VERY SHARP!

 

After all fixtures are installed, turn on the transformer.

D

Only for use with low voltage power units with a maximum output rating of 15V, 

300W per secondary.  
FOR LANDSCAPE LIGHTING SYSTEMS ONLY. OUTDOOR USE ONLY. THE DEVICE IS 

ACCEPTED AS A COMPONENT OF A LANDSCAPE LIGHTING SYSTEM WHERE THE 

SUITABILITY OF THE COMBINATION SHALL BE DETERMINED BY CSA OR LOCAL 

INSPECTION AUTHORITIES HAVING JURISDICTION.
ETL LISTED UNDER MODEL # U000-1708

Please read and save these instructions

A

B

C

E

D

Option 2

Option 1

Screw (E)

Screw (E)

Wire (C)

Connector (D)

Half brick 

light (B)

CAUTION: Safe for outdoor operation

WARNING: Install in accordance with all local codes and ordinances. 

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS 

IMPORTANT SAFETY INSTRUCTIONS

Option 3

Thumbscrew (B)

Отзывы: