THANK YOU
We appreciate the trust and confidence you have placed in Hampton Bay through the
purchase of this wireless push button. We strive to continually create quality products
designed to enhance your home. Visit us online to see our full line of products available for
your home improvement needs. Thank you for choosing Hampton Bay!
USE AND CARE GUIDE
WIRELESS PUSH BUTTON
Illustrations may vary from actual unit.
Safety Information
1.
Please read and understand this entire manual before attempting to assemble, install,
or operate this push button.
WARNING:
To prevent possible SERIOUS INJURY or DEATH never allow small children near
batteries. If battery is swallowed, immediately notify a doctor.
WARNING:
DO NOT DISPOSE OF BATTERIES IN FIRE. BATTERIES MAY EXPLODE OR LEAK.
NOTE:
The range of the wireless doorbell can vary with location, temperature, and battery
condition.
This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada.
Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
The user is cautioned that changes or modifications not expressly approved by the party
responsible for regulatory compliance could void the user’s authority to operate the
equipment.
Care and Cleaning
Use a dry cloth to clean the push button.
Do not use cleaners or polishes.
Do not use any fluids on the push button.
Pre-Installation
TOOLS REQUIRED
Phillips screwdriver
Small flathead screwdriver
PACKAGE CONTENTS
Part
Description
Quantity
A
Push button
1
B
Jumper
1
C
Screw
2
D
Double-sided tape
1
Battery - pre-installed (not shown)
1
Installation
1
Removing the battery tab
Remove the back of the push
button by pushing in the tab on the
bottom with a small screwdriver
(not included).
Remove the orange battery tab
from the push button.
2
Syncing the push button and
doorbell
Press and hold the “SYNC” button
on the doorbell until the doorbell
sounds a “Beep-Beep”.
Press the push button within 30
seconds. The doorbell will sound a
“Beep-Beep” tone to indicate the
push button is synced.
Press the push button to confirm
sync. If the doorbell sounds, sync
is complete.
SYNC – PRESS
AND RELEASE
.
RESET – HOLD
10 SECONDS.
TUNE – HOLD
1 SECOND.
30
3
Testing the push button and
doorbell
Temporarily position the push
button where you want it mounted.
Press the push button to verify
the doorbell and push button work
properly. If the doorbell does not
sound, see Troubleshooting.
NOTE:
Do not permanently mount the
push button until the push button and
doorbell are working properly.
SYNC – PRESS
AND RELEASE
.
RESET – HOLD
10 SECONDS.
CH
IM
E
V
O
LU
ME
TUNE – HOLD
1 SECOND.
UP
FRONT TRANS REAR
TYPE “C”
TYPE “C”
TYPE “C”
4
Mounting the push button
Use either screws or double-sided tape
to mount the push button.
To mount with screws, remove the
back of the push button by pushing
in the tab on the bottom with a
small screwdriver. Place the push
button back on the door jamb and
mark the two screw holes. Attach
with screws and snap on the front
of the push button.
When attaching the push button
with double-sided tape, remove
paper from both sides of the
double-sided tape and apply to a
clean surface.
5
Selecting a tune
Wireless doorbells have different selectable tunes. The wireless push button can be set
to play one of those tunes by adding or removing the jumper inside the push button.
See the table below for tune selection.
Doorbell Sound
Push Button Jumper ON
Rear door
Push Button Jumper OFF (factory default)
Front door
NOTE:
Refer to the doorbell manual for available tunes.
Push Button
Push Button
Jumper OFF
Jumper ON
Warranty
3-YEAR LIMITED WARRANTY
WHAT IS COVERED
This product is guaranteed to be free of factory defective parts and workmanship for a
period of 3 years from date of purchase. Purchase receipt is required for all warranty
claims.
WHAT IS NOT COVERED
This warranty does not include expendable items (such as light bulbs, batteries, etc.), repair
service, adjustment and calibration due to misuse, abuse or negligence. Unauthorized
service or modification of the product or of any furnished component will void this warranty
in its entirety. This warranty does not include reimbursement for inconvenience, installation,
setup time, loss of use, unauthorized service, or return shipping charges. This warranty
is not extended to other equipment and components that a customer uses in conjunction
with this product.
Contact the Customer Service Team at 1-844-760-3644 or visit www.hamptonbay.com.
Questions, problems, missing parts?
Before returning to the store, call Hampton Bay Customer Service
8 a.m. - 5 p.m., CST, Monday - Friday
1-844-760-3644
HAMPTONBAY.COM
Specifications
Power requirements
Type 2032 3V battery (included)
Troubleshooting
Problem
Solution
The doorbell does not sound.
Make sure batteries are installed according
to the diagram inside the push button and
doorbell (if applicable).
Check the charge of the push button and
doorbell batteries (if applicable) and replace
if necessary.
Make sure the plug-in doorbell has power
(if applicable).
Push button and doorbell are not synced.
Follow step 2 under Installation to sync.
The batteries seem okay, but the
doorbell does not work after installation.
Metal reduces transmission range. Use 1/4
in. to 1/2 in. (6 to 13 mm) wood shims to
move the doorbell or push button away from
the metal surface.
Concrete may reduce range. Move the
doorbell away from the concrete surface.
Locate the doorbell closer to the push
button.
208198-02A
A
B
C
D
Item #1001417372
Model #HB-7707-02
Item #1001417367
1001417369
Model #HB-7705-02
HB-7706-02
