halstrup-walcher PSD4 Series Скачать руководство пользователя страница 5

Страница: 5 / 39

Start-up

7100.006424_Bus description_PSD4xx_CA_H_ENG

08.04.2020

2 Start-up

WARNING

Risk of injury if used inappropriately.

The device must be installed by trained technical
personnel.

WARNING

Risk of burns due to hot drive.

The drive can become very hot during operation.

Allow the drive to cool before touching it.

WARNING

Risk of crushing due to rotary movement.

Do not reach into the working area of the drive when it is
still turning.

The user/operator must ensure appropriate protective
measures are taken.

WARNING

Incorrect assembly can lead to the destruction of the drive.

WARNING

Check that the supply lines are not pinched or crushed.

Lay the supply lines according to the general and specific
local assembly regulations.

If the supply lines have not been delivered together with
the device, please select suitable cables for the application.

Do not operate the positioning unit if the supply lines are
noticeably damaged.

WARNING

Risk of injury.

High contact voltages can occur in the case

of malfunctions.

This can be prevented by grounding.

ATTENTION

The drive must be protected against excessive heating.

The user/operator must ensure appropriate protective measures
are taken.

ATTENTION

Never apply force to the housing of the drive, e.g. for supporting
weight.

Содержание PSD4 Series








































Результаты поиска

Содержание PSD4 Series

Отзывы:

Похожие инструкции для PSD4 Series

Бренды по названию

Популярные бренды

halstrup-walcher PSD4 Series, Инструкция по эксплуатации

Результаты поиска

Содержание PSD4 Series

Отзывы:

Похожие инструкции для PSD4 Series

Бренды по названию

Популярные бренды