Halma Ocean Optics JAZ Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 70

background image

6: Maintenance

013-RD000-000-02-201510

47

6.

Delete the

OOI_USB.INF

in the INF directory. If your computer is running either the Windows

2000 or XP operating system, you must also delete the

OOI_USB.PNF

file in the INF directory.

7.

Navigate to the

Windows | System32 | Drivers

directory.

8.

Delete the

EZUSB.SYS

file.

9.

Reinstall your Ocean Optics application and reboot the system when prompted.

10.

Plug in the USB device.

The system is now able to locate and install the correct drivers for the USB device.

Mac Operating Systems

Since there are no device files for Jaz in a Mac operating system, you should not encounter any problems
if you installed the spectrometer before the OceanView software.

Linux Operating Systems

For Linux operating systems, all you need to do is install the OceanView software, then unplug and
replug in the spectrometer. Technically, the driver files for Linux simply give nonprivileged users
permission to use newly connected hardware. There isn’t any long-term harm to plugging in the device
before installing the software.

Jaz Troubleshooting Tips

The following table provides additional information for troubleshooting Jaz issues. If these suggested
solutions do not solve the problem, please contact us for Technical Support.

Problem

Possible Cause(s)

Suggested Solution(s)

Jaz does not initialize
correctly.

Unit was powered on too quickly
after being powered off.

Wait 10-15 seconds before powering
on Jaz.

USB Jaz turns on and
then powers down before
it completes initialization

Only the Jaz-DPU (CPU module)
+ Jaz-S (spectrometer module)
can be powered over USB (unless
the unit also includes a battery).
While a JAZ-DPU + JAZ-E
(Ethernet) + JAZ-S might
sometimes power over USB, the
available USB power may not
always successfully power the Jaz
stack.

Use the acc5V power
supply.

Jaz power LED doesn't
turn on (PoE, USB
operation or +5V power,
no battery).

Jaz needs to power its internal
electronics before it can fully
power up.

Wait 10 seconds after plugging in Jaz
before pressing the power button

Jaz display blanks out

Jaz has an automatic screensaver

While any key press will bring back

«
...
55
56
57
58
59
...
»

Содержание Ocean Optics JAZ







































































Отзывы:

Нет отзывов

Похожие инструкции для Ocean Optics JAZ

Бренд: Hach Страницы: 38

Бренд: Hach Страницы: 28

Бренд: Hach Страницы: 40

POCKET COLORIMETER II

Бренд: Hach Страницы: 142

Бренд: Hach Страницы: 4

Бренд: Hach Страницы: 308

Бренд: Hach Страницы: 158

Бренд: Hach Страницы: 118

POCKET COLORIMETER II

Бренд: Hach Страницы: 116

Бренд: Hach Страницы: 132

Бренд: Hach Страницы: 8

Бренд: Hach Страницы: 38

Бренд: Hach Страницы: 200

Бренд: MADDALENA Страницы: 4

Бренд: Macnaught Страницы: 4

Бренд: VeEX Страницы: 842

Бренд: Valcom Страницы: 1

Бренд: +GF+ Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды