HALE Silencer APS Series Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 146

HALE Silencer APS Series Скачать руководство пользователя страница 54

❑

Preventive Maintenance

54

Silencer Series Booster Pump

p/n: 029-0020-83-0

2.

Verify that the warning indicators in the cab and the pump control panel
function properly and agree with the indicators in the cab.

CAUTION !

MAKE SURE EVERYONE IS CLEAR OF THE APPARATUS. VERIFY THE PARKING
BRAKE IS SET AND THE WHEELS ARE CHOCKED TO PREVENT ANY MOVE-
MENT OF THE APPARATUS.

3.

Repair or replace any malfunctioning indicators.

Valve Maintenance

Properly functioning valves are integral to the operation of the pump. Refer to
the separate valve manual for proper valve maintenance procedures.

For example, lubricate all moving parts of the suction, discharge, hose drain,
and multi drain valves and valve linkage with a good grade, lithium base
grease.

Note: The PMD valve should be lubricated every six (6) months.

Transfer Valve Test (Two-Stage Pumps Only)

5.

For manual transfer valves:

6.

With the apparatus engine turned off, turn the handwheel between the vol-
ume and pressure positions a few times to verify that the valve operates
freely.

7.

Set the truck up for pumping per the procedure in Section 2, with the trans-
fer valve in the volume position.

8.

Leave the engine at idle speed and move the transfer valve to the pressure
position.

9.

Verify that the discharge pressure gauge readings have approximately dou-
bled.

10.

For power transfer valves:

11.

With the apparatus engine turned off, use either a 3/8-inch socket on the
indicator hex nut or a rod in the hole in the indicator hex nut to manually

«
...
52
53
54
55
56
...
»

Содержание Silencer APS Series



















































































































































Отзывы:

Нет отзывов