background image

1/8/04

USER OPERATION AND

MAINTENANCE MANUAL

HP SERIES

PORTABLE PUMPS

Pump
Serial
Number

A Hale Pump is a quality product:  ruggedly designed, accurately machined, carefully assembled and thoroughly tested.  In
order to maintain the high quality of your pump, and to keep it in a ready condition, it is important to follow the instructions on
care and operation.  Proper use and good preventive maintenance will lengthen the life of your pump.

ALWAYS INCLUDE THE PUMP SERIAL NUMBER IN CORRESPONDENCE.

Failure to follow the operating, lubrication, and maintenance
requirements set forth in this operating and maintenance manual
may result in serious personal injury and/or damage to equipment.

WARNING

MANUAL P/N 029-0020-24-0, REV E, © 2004 HALE PRODUCTS, INC., PRINTED IN U.S.A.

Hale Products cannot assume responsibility for product failure resulting from improper
maintenance or operation.  Hale Products is responsible only to the limits stated in the product
warranty.  Product specifications contained in this material are subject to change without notice.

HALE PRODUCTS, INC

.   A Unit of IDEX Corporation   700 Spring Mill Avenue   Conshohocken, PA  19428   TEL: 610-825-6300   FAX: 610-825-6440

Class 1 

 

607 NW 27th Avenue 

 

Ocala  FL  34475 USA  Tel: 352-629-5020 800-533-3569  Fax: 352-629-2902  

 

www.class1.com

Содержание HP 100









































































Отзывы: