HAKO Citymaster 2000 Скачать руководство пользователя страница 48

Страница: 48 / 186

3-20

X56b320.fm

Operation

3.4.2

Multifunction display

The Multifunction display

126

monitors a variety of functions and opera-

ting parameters of the vehicle. The multifunction display also provides

information as to the vehicle status and maintenance as well as mal-

functions.
The multifunction display is split into the top, middle and bottom areas. A

maximum of two operating parameters can be displayed at the same time.
Buttons

and

can be used to toggle between the individual operating

parameters. If an operating parameter is displayed for more than four

seconds, this status is saved and displayed when the ignition is turned on

again.

Operating parameters in the top area of the multifunction display:

In the middle area next to the Hako logo:

Fig. 19:

126

Symbol

Operating parame-
ter:

Unit: Remarks:

Engine revolutions

rpm

Total kilometres/miles km/mls Is permanently saved, cannot be dele-

ted

Daily kilometres/miles km/mls Is permanently saved, can be deleted

Vehicle operating
hours

h / min Is permanently saved, cannot be dele-

ted

Work hydraulics ope-
rating hours

h / min Is permanently saved, cannot be dele-

ted

Symbol

Operating parame-
ter:

Unit: Remarks:

Time

h:min -

Date

Day,

month

Service information

Displays the operating hours until the
next service time

Содержание Citymaster 2000



























































































































































































Результаты поиска

Содержание Citymaster 2000

Отзывы:

Бренды по названию

Популярные бренды

HAKO Citymaster 2000, Инструкция по эксплуатации и обслуживанию

Результаты поиска

Содержание Citymaster 2000

Отзывы:

Бренды по названию

Популярные бренды