HAKO Citymaster 2000 Скачать руководство пользователя страница 17

Страница: 17 / 186

X56b210.fm

2-1

Safety instructions

2 Safety instructions

2.1 Identification of warnings and dangers

Important indications regarding the safety of the operating personnel and

the vehicle are indicated in this operation manual with the following terms

and symbols:

Danger!

Failure to observe the instructions identified by this symbol may

result in personal injury or death for the operator or other

persons.

Measures for avoiding danger

Caution!

Failure to observe the instructions identified by this symbol may

result in damage to the vehicle.

Measures for avoiding danger for the vehicle

Important!

This symbol identifies instructions for a more efficient and economi-

cal use of the vehicle.

Environment!

Failure to observe the instructions identified by this symbol may

result in damage to the environment.

The environment is in danger if environmentally hazardous

material (e.g. waste oil) is not subject to proper use or disposal.

2.2 Warranty

Warranty claims can be made only if the conditions of warranty have been

observed. They are included in the General Conditions of Sales and Deli-

very for vehicles and spare parts manufactured or sold by Hako-Werke

GmbH, Federal Republic of Germany. Furthermore, the instructions in this

operation manual must be observed.

Содержание Citymaster 2000



























































































































































































Результаты поиска

Содержание Citymaster 2000

Отзывы:

Бренды по названию

Популярные бренды

HAKO Citymaster 2000, Инструкция по эксплуатации и обслуживанию

Результаты поиска

Содержание Citymaster 2000

Отзывы:

Бренды по названию

Популярные бренды