Hakko Electronics 850D Скачать руководство пользователя страница 1

Страница: 1 / 19

●

Thank you for purchasing the Hakko 850D SMD Rework
Station. This unit features digital control and display of hot
air temperature.
Please read this manual before operating the Hakko 850D.
Keep this manual readily accessible for reference.

●

SMD Rework Station

TABLE OF CONTENTS

PACKING LIST / SP ECIFICATIONS ..................................................... 1

SAFETY INSTRUCTIONS .................................................................... 2

PART NAMES ....................................................................................... 3

PREPARATION: ASSEMBLY AND ELECTRICAL CONNECTION ....... 4

OPERATION ......................................................................................... 5

PARAMETERS / INITIAL RESETTING ................................................ 7

USE ...................................................................................................... 8

MAINTENANCE / INSPECTION ........................................................ 10

ERROR MESSAGES ......................................................................... 11

TROUBLESHOOTING ....................................................................... 12

OPTIONAL NOZZLE .......................................................................... 13

PARTS LIST / STATION ...................................................................... 15

HANDPIECE ................................................................ 17

WIRING DIAGRAM ............................................................................ 18

Содержание 850D




















Результаты поиска

Содержание 850D

Отзывы:

Похожие инструкции для 850D

Бренды по названию

Популярные бренды

Hakko Electronics 850D, Инструкция по эксплуатации

Результаты поиска

Содержание 850D

Отзывы:

Похожие инструкции для 850D

Бренды по названию

Популярные бренды