Safety Precautions
Á ¢¼
´Ó ÃÓ
ÚÏ ´Ô
¡
²
»
¿
É
Ò
Ô
Á
¢¼
´Ó
ÃÓ
ÚÏ
´Ô
¡
²
»¿
ÉÒ
Ô
For first use after installation, the tank must be
full of water before connecting the power.
Otherwise, heating element overheat may
cause troubles.Children taking shower must be
attended by adults.
Please do not point the showerhead towards
human body when turning on or off the faucet,
avoiding to be scalded by a small stream of
hot water.
Haier
C
In winter in cold regions, for long-term out-of-
use, please lift the safety valve handle to empty
the water, avoiding ice formation damaging the
water heater.
Damaged power cord must be replaced by
after-service technicians with special cable
(factory provided). Other persons shall not
dismantle or repair. In addition, do not place
flammable matters nearby the water heater.
Do not use damaged wire, socket or appliances
with loose plug, otherwise accidents like
electric shock, short circuit and fire may occur.
Make sure power plug closely fits with power
socket.
²
»Ð
У
¡
²
»Ð
Ð
Power socket for water heater shall be
located in a dry place free of water spray. Do
not insert or pull the power plug with wet
hands, for accidents like electric shock or
injury may happen.
Temperature value indicated on the display is for water around the detection point. Outlet water
temperature is generally higher. Before use, please first turn on cold water and then adjust water
temperature as you need. During use, the displayed value is still water temperature at detection point
instead of outlet temperature. Please do not directly turn on hot water.
The product adopts Haier
Safe Care
patented technology. In normal installation, even in severe
case that ground wire is live due to wrong connection, the product
Safe Care
technology can filter
and efficiently ensure your safety. However, whenever your feel a sensory current, please pull out the
power plug and notify local after-service men in time. Do not dismantle by yourself.
Check if power meter and wire size are consistent
with water heater rated current. If necessary, ask
experienced qualified electricians to check.
The water heater shall use 230 V~ / 50 Hz
power supply from a separate socket (no
m u l t i - p u r p o s e s o c k e t ) a n d b e r e l i a b l y
grounded. Power plug pins shall be cleaned
in time to avoid any contamination causing
accidents like fire.
Operation Instructions
9. Delay Time Setting
Delay function means that, system automatically calculates the time needed to reach
temperature setting value with a defaulted 2150 W power, then determines the time to
start heating, and automatically heats to the set temperature before the preset delayed
time to use hot water. Two Delay Times (Time 1 + Time 2) means machine as needed can
heat water in two delayed use times. This machine can be manually set two delayed water
use times. Setting will take PC clock time as reference. Defaulted Time 1 use time is 17:00
and Time 2 use time is 06:00. In Delay mode, system default heating power 2150 W can't
be adjusted.
Example: as shown in Fig. 12, set delayed use Time 1 at 10:30.
With machine powered on, consecutively press Mode button until it enters Time 1
operation status with delay indication and symbol
lighted. Press Set button to enter
Time 1 hour setting status with Time 1 hour digits flashing. Press
or
button to get
10:00. While hour digits are flashing, you can press Set button to confirm and enter Time 1
minute setting. Adjust the value to 10:30 with
or
button.
Then you may press Set button to confirm current settings or wait 6 s after which
machine automatically confirms and quits. Time 2 time setting is similar to Time 1, i.e.
press Mode button to enter Time 2 operation mode and set Time 2 time with Set button.
Note: If large quantity hot water is used after delay mode is started and water heaters
starts heating, resulting in water heater still hasn't reached temperature setting at delayed
use time, machine will automatically extend heating for half an hour and stops. If actual
temperature has reached setting value before delayed use time, and it decreases before
reaching delayed use time, machine will calculate heating time again and determines if re-
heating is needed or not. Likewise, if water heater hasn't reached set temperature at
delayed use time due to too low supply voltage, machine also automatically extends for
half an hour and stops.
10. Operation Mode Selection
After powering on, by consecutively pressing Mode button, system will shift between
Real-time Heat / Warm (with Real-time indication), Medium Warm (with Medium Warm
indication), Night Power (with Night Power indication), Time 1 (with Delay and
indication), Time 2 (with Delay and
indication) ,Time 1 + Time 2 (with Delay and
,
indication) and Intelligent (with Intelligent indication) modes. User can select any mode as
current operation mode. Only after being selected as current operation mode,
corresponding settings can be executed.
Example: clock at 7:00, heating power of 2150 W, temperature setting of 75
(temperature
setting and actual temperature flash alternatively), delayed useTime 1 being set at 10:00.
If you want to use water at 10:00, machine will automatically heats water to set
temperature at 10:00. Otherwise (e.g. in Night Power mode as shown in Fig. 13), it doesn't
execute Time 1 function. You need to select Delay and symbol
with Mode button, and
then Time 1 function can be executed.
11. Powering Off
After taking shower, you can lightly press On/Off button to power off the machine.
Hints:
With machine powered on, you can press Set button to set On/Off time for various
modes, and adjust time with
or
button. In Real-time Heat mode, you can press Set
button to adjust clock hour and minute values. In Delay mode, you can press Set button
to set delayed use time. In Medium Warm and Intelligent mode, Set button is inactive.
The machine has multiple safety means like current leakage protection, over-
temperature protection, sensor short-circuit and open-circuit protection, which can
realize full disconnection and display fault code. All fault protections are unrecoverable
protection which needs local after-sales service.
This water heater has power failure memory function. You needn't re-set heating power
level, heating temperature ,clock and operation mode. Machine will directly go to
previous working status after powering on again.
A.
B.
C.
Never do that
Be sure to act as per instructions
Description of the Symbols
