background image

INSTALLATION AND ACCESSORY PARTS

Usage of the drain hose

       Hang  the outer drain hose on the proper place
before washing( do not use it toppled down
on the ground).

Attend that the outlet of drain hose shall be higher

than  the water level in  washtub  to avoid siphon
phenomenon.

1.0m<h<1.5m

Connect the water inlet hoses

Figure 2

Figure 1

C

H

1. Attach the water inlet hoses to the hot water faucet and the cold water 
    faucet. Using pliers, tighten the coupling.  ( As figure 1)

4. Check for leaks
   (1). Swing the water inlet  hose gently to confirm if it is suitable.
   (2). Turn on the water faucets and check for leaks. A small amount of water might 
         enter the washers. You will drain this later.

3. Attach the hose connected with hot water faucet to the HOT water inlet valve(sign
    with "H'). Attach the hose connected with cold water faucet to the COLD water 
   valve(sign with

C

 ). ( As figure 2)

NOTE

:  Do not over-tighten. 

2. Run water through both faucets and inlet hoses, into a bucket or laundry tub, to get
    rid of particles in the water lines that might clog the inlet valves screens.

Install the drain hose

Outer drain hose

 component

Drain hose neck

Drain  hose joint

Drain hose hoop

       First install the drain hose hook on the parts of 
outer drain hose component.

       Put the drain hose clamp on the outer drain hose,
insert the outer drain hose into the joint for it, and
then clutch tightly with drain hose hoop.

Содержание HLT364XXQ - Genesis Washer



























Отзывы: