Haier GE PTW600BPR DG Series Скачать руководство пользователя страница 48

Страница: 48 / 77

– 48 –

3. Unplug the speed sensor which is attached to

the stator assembly.

4. Remove three fasteners hex-head screw

which is securing stator to the platform and

pull up the stator assembly.

5. Slide down the speed sensor with harness to

release from stator motor.

The direct drive motor is a three-phase motor.

The three-phase inverter is incorporated into the

main board and provides to power the direct drive

motor. The direct drive motor consists of a rotor

and stator.

Direct Drive Motor Diagnosing

The output voltage from the inverter to the motor

is variable and should not be tested. The direct

drive motor resistance may be verified at the main

board, J1001, 5.8-ohms between pins 6 and 7, 7

and 8, 6 and 8.

Direct Drive Motor Removal

1. Unclip the main harness from the motor

connector by pushing down on the connector

clip. The clip is large enough that it can be

done with one hand. The motor side of the

harness is secured in place.

2. Remove rotor nut that secure the stator and

rotor and pull up the rotor.

Direct Drive Motor

Rotor Nut

Rotor

Fasteners

Speed Sensor

Connector

Mode Shifter

Connector

Sensor

Содержание GE PTW600BPR DG Series














































































Результаты поиска

Содержание GE PTW600BPR DG Series

Отзывы:

Похожие инструкции для GE PTW600BPR DG Series

Бренды по названию

Популярные бренды

Haier GE PTW600BPR DG Series, Техническое обслуживание руководство

Результаты поиска

Содержание GE PTW600BPR DG Series

Отзывы:

Похожие инструкции для GE PTW600BPR DG Series

Бренды по названию

Популярные бренды