Haier GE PTW600BPR DG Series Скачать руководство пользователя страница 47

Страница: 47 / 77

– 47 –

5. Unclip the main harness from the motor

connector by pushing down on the connector

clip. The clip is large enough that it can be

done with one hand. The motor side of the

harness is secured in place.

6. Remove the two hex-head bolts that secures

the motor to the platform. When reinstalling

the bolts, torque to 170-in. pounds.

NOTE

: If removing the motor with the washer

leaning back, be sure to support the weight of the

motor, as it will drop away from the platform once

the second bolt is removed.

Drive Belt Motor

The belt drive motor is 1/2 horsepower. They are

model specific, and each have a specific drive

belt.

Drive Belt Motor Diagnosing

The motor requires 120 VAC.

Remove the harness side connector going to the

motor, then check the resistance (motor windings)

on the motor itself as follows:

• Between pin 1 and pin 2 of the motor

connector, resistance should be between 2.8-

ohms and 4.2-ohms.

• Between pin 1 and pin 3 of the motor

connector, resistance should be between 2.8-

ohms and 4.2-ohms.

Drive Belt Motor Removal

1. Unclip the hall sensor from the motor.

2. Remove belt protector and belt (see

Belt

Protector Removal

and

Belt Removal

under

Drive Belt

in this section of the service guide.

3. Remove drive/transmission pulleys (see

Pulley Removal

under

Drive/Transmission

Pulleys

in this section of the service guide).

4. Remove the speed/hall sensor (see

Speed/

Hall Sensor Removal

under

Speed/Hall

Sensor

in this section of the service guide).

3. There is a locating post on the bottom of the

sensor that is pushed into an existing hole in

the motor housing when reinstalling.

Содержание GE PTW600BPR DG Series














































































Результаты поиска

Содержание GE PTW600BPR DG Series

Отзывы:

Похожие инструкции для GE PTW600BPR DG Series

Бренды по названию

Популярные бренды

Haier GE PTW600BPR DG Series, Техническое обслуживание руководство

Результаты поиска

Содержание GE PTW600BPR DG Series

Отзывы:

Похожие инструкции для GE PTW600BPR DG Series

Бренды по названию

Популярные бренды