Haier GE NS22HM Скачать руководство пользователя страница 1

Страница: 1 / 26

508311G01 / 31-5000754

Page 1 of 26

Issue 2250

GE Appliances

A Haier Company

Appliance Park

Louisville, KY 40225

(P) 508311G01

*P508311G01*

Table of Contents

Application ...................................................................1

General ........................................................................2

Installation ...................................................................2

Refrigerant Piping ........................................................4

Electrical - Circuit Sizing and Wire Routing ...............14

Thermostat Control and Low Voltage Control Wiring 14

Outdoor Unitary Control.............................................18

Unit Operation ...........................................................20

Start-Up .....................................................................20

Maintenance ..............................................................23

Homeowner Information ............................................23

Start-Up and Performance Checklist .........................26

This manual must be left with the homeowner for future reference.

This is a safety alert symbol and should never be ignored. When you see this symbol on labels or in manuals, be alert to

the potential for personal injury or death.

Installation and servicing of air conditioning equipment

can be hazardous due to internal refrigerant pressure

and live electrical components. Only trained and

qualified service personnel should install or service

this equipment. Installation and service performed by

unqualified persons can result in property damage,

personal injury, or death.

WARNING

Sharp metal edges can cause injury. When installing

the unit, use care to avoid sharp edges.

WARNING

ELECTRICAL SHOCK HAZARD!

Risk of electrical shock. Disconnect all

remote power supplies before installing

or servicing any portion of the system.

Failure to disconnect power supplies

can result in property damage, personal

injury, or death.

WARNING

Application

These units are designed for use in residential and light

commercial type buildings. Units should be installed with

approved indoor matches listed in the Air-Conditioning,

Heating and Refrigeration Institute (AHRI) Directory of

Certified Products. Refer to http://www.ahridirectory.org.

The Clean Air Act of 1990 bans the intentional venting

of refrigerant (CFCs, HCFCs and HFCs) as of July

1, 1992. Approved methods of recovery, recycling or

reclaiming must be followed. Fines and/or incarceration

may be levied for noncompliance.

IMPORTANT

INSTALLATION INSTRUCTIONS

NS22HM

Variable Capacity Heat Pump

Содержание GE NS22HM



























Результаты поиска

Содержание GE NS22HM

Отзывы:

Похожие инструкции для GE NS22HM

Бренды по названию

Популярные бренды

Haier GE NS22HM, Руководство по установке

Результаты поиска

Содержание GE NS22HM

Отзывы:

Похожие инструкции для GE NS22HM

Бренды по названию

Популярные бренды