Haier GE GDF510P M4 Series Скачать руководство пользователя страница 45

Страница: 45 / 79

– 45 –

After the door check, the control will enter a mode

to display any error codes that are currently

detected by the control.

If any of the above LED’s illuminate, it indicates

the fault condition is present. These fault

displays cannot be cleared manually; they will

be automatically cleared by the control when the

fault condition is no longer present.

Consumer Error Mode will time out after 5

minutes.

ANY KEY PRESSES OTHER THAN CYCLE

SELECT EXIT THIS MODE.

LED

Error Type

Error Causes

Start

Communications

Failure

User Interface

control unable to

communicate with

machine control.

Heated

Dry

Wash

Temperature

Error

Minimum wash

temperature of

120°F was not

reached in 3 of the

past 5 wash cycles.

Wash

Boost

Thermistor Error Control detecting

short or open

circuit at thermistor.

Clean Turbidity Sensor

Error

Control detecting

short or open

circuit at turbidity

sensor. May also

occur on models

without turbidity

sensor.

Lock Always

Illuminated

Illuminates when

Error Code Display

Mode is active.

Electronic Controls

The main control board is located under the

dishwasher. It is supplied 120 VAC from the

consumer's home. Outputs include 120-volt AC

to the heating element, wash and drain motors.

The control also supplies 13.5 VDC to the fill

system, door switches, turbidity sensor (some

models), User Interface (UI) board and detergent

module in the door.

The main control has a

CSM

(Current Sense

Module) located on the control, if the CSM

detects a ground path the dishwasher will be non-

responsive.

CSM

(

urrent

ense

odule)

Introduction

A CSM is a protective device that is located on

the main control of GEA Dishwashers. This

device is designed to trip if current leakage to

ground is above 20mA ± 5mA if detected. The

CSM functions similar to commercially available

GFCI's, if tripped the dishwasher will be non-

responsive.

The CSM may be reset by the consumer by

cycling the house electrical supply to the

dishwasher.

NOTE

: The dishwasher MUST be grounded and

never operated without a ground connection.

Consumer Error Mode

To Enter Consumer Error Mode

With the dishwasher in Standby Mode (not

running a cycle), press and hold the Cycle Select

and Start buttons simultaneously for 5 seconds.

On entry into the Consumer Error Mode, the

control reports the door status for 10 seconds.

• All LED's are solidly illuminated, if the door is

detected as closed.

•

All LED's are flashing, if the door is detected

as open.

Содержание GE GDF510P M4 Series
















































































Результаты поиска

Содержание GE GDF510P M4 Series

Отзывы:

Похожие инструкции для GE GDF510P M4 Series

Бренды по названию

Популярные бренды

Haier GE GDF510P M4 Series, Руководство по обслуживанию

Результаты поиска

Содержание GE GDF510P M4 Series

Отзывы:

Похожие инструкции для GE GDF510P M4 Series

Бренды по названию

Популярные бренды