Haier GE GDF510P M4 Series Скачать руководство пользователя страница 36

Страница: 36 / 79

– 36 –

Stainless Steel (SS) Door Attach Strips

Attachment strips are used on stainless steel

(SS) door attach strips models only; plastic inner

doors have this feature molded into them. Strips

also have a boss on each side for the screw to

secure the inner and outer door panels.

Attachment Strips Removal

1. Remove and separate the inner and outer

door panels.

2. Remove the front control console or top

control panel.

3. Remove the two T15 Torx-head screws on the

side attach strips.

4. Slide the strip inward to remove.

5. To remove the top attach strip, slide the strip

down after the top console and side attach

strips have been removed.

Outer Door Panel Components

Bar Handle

The bar handle is attached to the outer door

panel. The handle is an assembly with end caps

pre-attached.

Bar Handle Removal

1. Remove and separate the door.

2. Remove the vent conduit (two 1/4-inch hex-

head screws).

3. Remove two 3/8-inch hex-head, 1/4 -28

thread size screws holding the handle.

Bar Handle

Handle Brackets

Handle Screws

Vent Insulation

Vent Gasket

Vent Conduit

Gasket

Insulation

Badge

Pad

(SS Inner Door Models)

Cross Brace

(SS Inner

Door Models)

Outer Door Panel

Inner Door Panel

Top

Console

Side Attach

Strip

Side Attach Strip

Screws

(T15 Torx)

Top Attach Strip

Side Attach Strips

Cross

Brace

Screws

Содержание GE GDF510P M4 Series
















































































Результаты поиска

Содержание GE GDF510P M4 Series

Отзывы:

Похожие инструкции для GE GDF510P M4 Series

Бренды по названию

Популярные бренды

Haier GE GDF510P M4 Series, Руководство по обслуживанию

Результаты поиска

Содержание GE GDF510P M4 Series

Отзывы:

Похожие инструкции для GE GDF510P M4 Series

Бренды по названию

Популярные бренды