Haier GE GDF510P M4 Series Скачать руководство пользователя страница 13

Страница: 13 / 79

– 13 –

Critical errors will turn a cycle off and show a display alerting the consumer of a fault which will not

allow the dishwasher to function or cause an undesirable condition.

No Water Detected

In the event the internal water level does not change, the cycle will be cancelled and the user interface

will display the following:

•

Models with SSD (Seven Segment Display) Screens

: H20 will be displayed on the SSD screen.

• Models without SSD Screens

: Wash Temp LED will blink continuously.

Water may be turned off. The consumer is directed to verify the water supply line is connected properly,

the supply line valve is turned on, and then restart the cycle. If this fails, the consumer is directed to

call for service.

Pressure Sensor Errors

In the event that the pressure sensor signal is undetectable or out of range, the cycle will be canceled

and the user interface will display the following:

• Models with SSD

: PrS or PrF will be displayed.

• Models without SSD

: Dry LED or Wash Temp+Dry LEDs will blink.

The control does not see a change in pressure during fill. Verify pressure sensor harness, then replace

the pressure sensor if needed.

Continuous Fill Error

In the event that consecutive signals from the pressure sensor detect high water level, the drain pump

will run and the User Interface (UI) will display the following:

• Models with SSD Screens

: CFE will be displayed on the SSD screen.

• Models without SSD Screens

: Cycle Indication LEDs will blink continuously.

The consumer is directed to turn off the water supply. Diagnose reasons for the water valve not

shutting off.

Critical Errors

Содержание GE GDF510P M4 Series
















































































Результаты поиска

Содержание GE GDF510P M4 Series

Отзывы:

Похожие инструкции для GE GDF510P M4 Series

Бренды по названию

Популярные бренды

Haier GE GDF510P M4 Series, Руководство по обслуживанию

Результаты поиска

Содержание GE GDF510P M4 Series

Отзывы:

Похожие инструкции для GE GDF510P M4 Series

Бренды по названию

Популярные бренды