Haier GE DDT700S N0 Series Скачать руководство пользователя

Страница: 35 / 78

– 35 –

SS Door Attach Strips

Attachment strips are used to help secure the

inner and outer door panels.

Side Attachment Strip(s) Removal

1. Remove and separate the inner and outer

door panels.

2. Remove the front control console or top

control panel.

3. Remove the two T15 Torx screws on the side

attach strips.

4. Slide the strip inward to remove.

Top Attachment Strip Removal

The door strike must be removed first (see

Door

Strike

, in this section of this service guide).

The top attach strip may now be removed by

sliding the strip down (the side attachment strips

must be removed first).

With the User Interface (UI) and Console (pocket

handle on front control models) removed, there

is clear access to the 1/4-in. hex-head screw that

secures the strike to the inner door and top attach

strip.

Remove the 1/4-in. hex-head screw, remove the

door strike. Top attachment strip may now be

removed.

Side Attach

Strip

Side Attach Strip

Screws (T15 Torx)

Top

Console

The inner door panel must be replaced to replace

the door gasket (bottom of the door).

1/4" hex-head screw

secures door strike

Door strike

Attachment strip

Mounting screw

Inner Door Panel

Door Strike

Door Gasket

Содержание GE DDT700S N0 Series















































































Результаты поиска

Содержание GE DDT700S N0 Series

Отзывы:

Похожие инструкции для GE DDT700S N0 Series

Бренды по названию

Популярные бренды

Haier GE DDT700S N0 Series, Техническое обслуживание руководство

Результаты поиска

Содержание GE DDT700S N0 Series

Отзывы:

Похожие инструкции для GE DDT700S N0 Series

Бренды по названию

Популярные бренды