Haier GE DDT700S N0 Series Скачать руководство пользователя

Страница: 33 / 78

– 33 –

All UI's (User Interface's) are Cap (Capacitance)

Touch. There are no buttons, light pipes or

sealing components. The front or top console

(depending model) is assembled to the UI and

available as one component.

Example of Cap Touch Console Front

Example of Cap Touch Console Rear

Model GDF565 UI is part of the front console.

To remove all other front control UI's, separate the

door, disconnect the wire harness and remove

four 1/4-in. hex-head screws.

The control will be removed from the front

The top control User Interface (UI) come as an

assembly, including the top console, UI and

bottom console

To remove the UI assembly, remove five 1/4-in.

hex-head screws from the top control.

Some models have a display on the front panel, it

is secured to the bottom of the UI assembly with

one 1/4-in. hex-head screw. The lens is adhered

to the outer door panel.

Lens

Display

User Interface (UI)

Top Control User Interface (UI)

Содержание GE DDT700S N0 Series















































































Результаты поиска

Содержание GE DDT700S N0 Series

Отзывы:

Похожие инструкции для GE DDT700S N0 Series

Бренды по названию

Популярные бренды

Haier GE DDT700S N0 Series, Техническое обслуживание руководство

Результаты поиска

Содержание GE DDT700S N0 Series

Отзывы:

Похожие инструкции для GE DDT700S N0 Series

Бренды по названию

Популярные бренды