Haier GE DDT700S N0 Series Скачать руководство пользователя

Страница: 27 / 78

– 27 –

Left Side

Right Side

The third rack is designed to place silverware,

cutlery and other utensils at the top of the

dishwasher for easier access.

To Remove the Basket and Frame as an

Assembly:

1. Pull the rack out to full extension.

2. Lift and continue to pull the rack out.

3. When rear rollers contact the stop, lift and

continue to pull the rack off the rails.

The rails may be removed by releasing the rear

end cap. Push the tab and remove the endcap.

There are a variety of silverware baskets and

configurations available. Consult the Owner’s

Manual for silverware basket information.

(

Continued next page

)

The left and right brackets and covers are

different part numbers and are marked L or R (left

or right) on the inside to insure proper installation.

Silverware Baskets

Third Rack (Some Models)

Содержание GE DDT700S N0 Series















































































Результаты поиска

Содержание GE DDT700S N0 Series

Отзывы:

Похожие инструкции для GE DDT700S N0 Series

Бренды по названию

Популярные бренды

Haier GE DDT700S N0 Series, Техническое обслуживание руководство

Результаты поиска

Содержание GE DDT700S N0 Series

Отзывы:

Похожие инструкции для GE DDT700S N0 Series

Бренды по названию

Популярные бренды