background image

                   Your air conditioning product is marked with this

                   symbol.This means that electrical and electronic

                   products shall not be mixed with unsorted

                   household waste.Do not try to dismantle the

                   system yourself:the dismantling of the air

conditioning system,treatment of the refrigerant,of oil and of

other part must be done by a qualified installer in accordance

with relevant local and national legislation.Air conditioners

must be treated at a specialized treatment facility for reuse,

recycling and recovery.By ensuring this product is disposed

of correctly,you will help to prevent potential negative cons-

equences for the environment and human health.Please

contact the installer or local authority for more information.

Battery must be removed from the remote controller and dis-

posed of separately in accordance with relevant local and

national legislation.

The products are fulfilled with the requirements in the

directive 2011/65/EU of the European parliament and of

council on the Restriction of the use of Certain Hazardous

Substances in Electrical and Electronic Equipment(EU

RoHS Directive)

WEEE

In accordance with the directive 2012/19/EU of the European

parliament,herewith we inform the consumer about the dis-

posal requirements of the electrical and electronic products.

DISPOSAL REQUIREMENTS:

Contains fluorinated greenhouse gases

 covered by the Kyoto Protocol

This product contains fluorinated greenhouse gases covered

by the Kyoto Protocol.Do not vent into the atmosphere.

Refrigerant type:R32

GWP*value:675

GWP=global warming potential

Please fill in with indelible ink,

 

1      the factory refrigerant charge of the product

 

2      the additional refrigerant amount charged in the field

            and

 

1+2  the total refrigerant charge

 on the refrigerant charge label supplied with the product.

 The filled out label must be adhered in the proximity of the

 product charging port(e.g.onto the inside of the stop value

 cover).

 A contains fluorinated greenhouse gases covered by the

 Kyoto Protocol

 B factory refrigerant charge of the product:see unit name

 plate

 C additional refrigerant amount charged in the field

 D total refrigerant charge

 E outdoor unit

 F refrigerant cylinder and manifold for charging

Air conditioner working temperature: cooling -10~46 degree, heating -15~24 degree.

The single indoor unit will reduce in heating  efficiency if the ambient temperature is under 0 degree.

WARNING

IMPORTANT INFORMATION REGA-

RDING THE REFRIGERANT USED

1

A

B

C

D

kg

kg

kg

R32

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly

qualified persons in order to avoid a hazard.

This appliance is not intended for use by persons (including children) with reduced physical, sensory

or mental capabilities, or lack of experience and knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

This appliance can be used by children aged from 8 years and above and persons with reduced physical,

sensory or mental capabilities or lack of experience and knowledge if they have been given supervision

or instruction concerning use of the appliance in a safe way and understand the hazards involved.

Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children

without supervision.

The appliances are not intended to be operated by means of an external timer or separate remote-

control system.

Keep the appliance and its cord out of reach of children less than 8 years.

The A-weighted sound pressure level is below 70 dB.

This appliance is intended to be used by expert or trained users in shops, in light industry and on farms,

or for commercial use by lay persons.

Disconnect the appliance from its power source during maintenance service and when replacing parts.

Содержание 3U55S2PR1FA

































Отзывы: