S
PECIFICATIONS
P7000
Power Rating ..................................................................... 350 Watts/channel @ 8
Ω
500 Watts/channel @ 4
Ω
*
1000 Watts bridged/mono @ 8
Ω
*
Total Harmonic Distortion (THD) ................................................ <0.2% (20Hz-20kHz)
Signal-to-Noise .......................................................................... 100dB “A” Weighted
Full Power Bandwidth ..................................................... 0.2Hz to 100kHz (+0/–3dB)
Slew Rate ....................................................................................................... 100V/
µ
s
CMRR (Common Mode Rejection Ratio) .............................................. 75dB at 1kHz
Input Impedance ........................................................... 47k
Ω
per phase balanced
Gain ................................................................................... +15dB min. / +30dB max.
Input Sensitivity Range .................... 850mV to 4.75V (@ 8
Ω
) per phase balanced
700mV to 4V (@ 4
Ω
) per phase balanced
Damping Factor ..................................................................................... 600 (to 1kHz)
200 (to 10kHz)
25 (to 100kHz)
Power Consumption .......................................... 200W / 2.3A @ 120VAC (idle power)
470W / 5.2A @ 120VAC (1/8 power – 8
Ω
)
1100W / 12A @ 120VAC (max. power – 8
Ω
)
Indicators .................................................. Power, Signal, Clipping, Thermal, Short
Dimensions ................................................... 19”W x 12
7
⁄
8
”D** x 3
1
⁄
2
”H (2-rack spaces)
(48.3cm x 32.7cm x 8.9cm)
Net Weight ......................................................................................... 40 lbs. (18.18kg)
*Continuous power limited by current rating of line fuse. **plus 1
1
/
8
” for handles
A
m
p
l
i
f
i
e
r
P7000
®
A
RCHITECT
’
S
AND
E
NGINEER
’
S
S
PECIFICATIONS
The audio power amplifier shall be solid state design employing 16 lateral
power MOSFET output devices. It shall be constructed on a 16 gauge steel
chassis utilizing forced air cooling and be technician friendly using modular
construction.
Each channel shall be rated for a minimum of 350 watts into an 8 ohm load and
500 watts* into a 4 ohm load with both channels driven. In bridged mono mode,
the amplifier shall produce at least 1000 watts* into an 8 ohm load. A switch
shall be provided for stereo or bridged mono operation and all power ratings
shall be measured from 20Hz-20kHz with less than 0.2% THD.
The amplifier’s back panel shall provide Balanced inputs via combination XLR
and 1/4” phone jacks. The back shall also utilize gold-plated 5-way binding
posts for output connectors and a switch to isolate or connect the signal
ground to the chassis ground. Each amplifier channel shall incorporate dual
2nd order Butterworth crossovers. The amplifier shall include a 3-wire grounded
AC line cord and UI power transformer operating on 120V/60Hz AC mains. An
optional transformer for 230V 50-60Hz operation shall be available.
The amplifier’s front panel shall provide level controls with optional security
covers. The front shall also incorporate a lighted main power switch and
indicators for each amplifier channel. The indicators shall display signal
present when 30mV of signal is detected, signal clipping when distortion rises
above 1%, thermal protection should the heatsink temperature become exces-
sive, and short circuit protection in case a problem on the speaker system
arises.
The amplifier shall fit standard 19” EIA rack mounting requirements utilizing 2-
rack spaces and have handles. The dimensions shall be 19” Wide, 12
7
⁄
8
”
Deep**, 3
1
⁄
2
” High, and be finished in black with a net weight of 40 pounds. It
shall be a Hafler P7000.
*Continuous power limited by current rating of line fuse. **plus 1
1
/
8
” for handles
15A SLO BLO
CH 2
120VAC/60Hz
1500W MAX
CH 1
(Mono/Biamp)
Audio Ground
Chassis
Stereo
Float
Biamp
CH 2
–
+
–
+
– +
Mono
XCard
Side View
• Set Switches to
Stereo and Normal
• Connect Input Signals
to CH1 and CH2
• Set Gains and Crossovers independently
Stereo:
• Set Switch to
Bridged Mono
• Use CH 1 input ONLY
• Set Gains and Crossovers
on CH 1 ONLY
Bridged Mono:
• Set Switch to
Biamp and Normal
• Use CH 1 input ONLY
• Set Gains and Crossovers
independently
Biamp:
• Remove Cover
• Configure Crossovers as shown
• Each XCard provides 12dB/octave
LP or HP in series
Crossovers:
HP
High-Pass
LP
Low-Pass
FULL
Full Range
3
2
1
+
–
XLR Connections
Phone Connections
+
–
S/N
!
CH1
4-8
Ω
8
Ω
4-8
Ω
A Division of Rockford Corp.
Tempe, AZ 85281 U.S.A.
Designed & Assembled in the U.S.A.
®
PUSH
PUSH
CAUTION:
For continued
protection against
risk of fire, replace
with same type and
rating of fuse.
C A U T I O N
RISK OF ELECTRIC SHOCK
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
REFER SERVICING
TO QUALIFIED PERSONNEL
L U C A S F I L M
®
