background image

P3100™ Power Amplifier

Hafler

Passion for Perfection

Bridged Mono

For systems with high power requirements, the amplifiers can be configured for single channel bridged mono operation. To bridge the 

amplifier, set the rear panel MONO switch to the Mono (In) position. The Channel 1 input and level control is used and the Channel 2 

level control must be set to its maximum gain position. The speaker is connected to the RED output binding posts.

When the amplifier is bridged the output is floating. Any speaker which requires a common ground from the amplifier output 

cannot be used in this application.

Since a bridged amplifier shares the load between the two channels, each channel will effectively drive half of the load. For 

bridged mono operation we recommend using an 8 Ohm load as the minimum impedance. Less than 8 Ohm operation in 

bridge mode is outside the operating parameters for the P3100 and should not be done.

5

MONO

Pushed “in”

8 Ohm

8 Ohm

MONO

Pushed “in”

MINIMUM RECOMMENDED SPEAKER CABLE GAUGE

Distance

8 Ohm (150W)

4 Ohm (200W)

8 Ohm - Bridged Mono (400W)

10’ (3m)

16 AWG (1.29mm)

14 AWG (1.63mm)

16 AWG (1.29mm)

20’ (6m)

14 AWG (1.63mm)

10 AWG (2.59mm)

14 AWG (1.63mm)

30’ (9m)

12 AWG (2.05mm)

8 AWG (3.26mm)

12 AWG (2.05mm)

50’ (15m)

10 AWG (2.59mm)

6 AWG (4.12mm)

10 AWG (2.59mm)

100’ (30m)

6 AWG (4.12mm)

N/A

6 AWG (4.12mm)

Содержание P3100





















Отзывы: