Hafele 940.41.043, Инструкции по установке и эксплуатации

Страница: 14 / 44

H
D
E
1
1
.0
5
.2
0
1
0
Ma
ß
e
i
n
m
m
–
D
im
e
n
si
o
n
s
in
mm
–
D
im
e
n
si
o
n
s
e
n
mm
–
Me
d
id
a
s
e
n
mm
-
Mi
su
re
i
n
m
m
-
D
im
e
n
sõ
e
s
e
m
mm
14/44
2. REFERENCE TO ILLUSTRATIONS
The given operating and performance features can only be guar-
anteed with the use of HÄFELE accessories and safety devices.
2.1 Standard installation references (fig. 1-4)
[1] Actuator
[2] Radar
[3] Push-button
panel
[4] Connect the power supply to a wall socket
2.2 Automation references (fig. 2-5)
[5] Gearmotor with control panel
[6] Transmission
[7]
Door wing connection bracket
[8] Belt
[9]
Door wing blocking device
[10] Radio receiver
3. INSTALLATION
Unless otherwise specified, all measurements are expressed
in millimetres (mm).
3.1 Case fastening
- If necessary shorten the length of the case (transmission
side) to the dimension of the door passage opening.
Attention: reposition the components correctly inside the case
after cutting. The transmission pulley [6] and the gearmotor pulley
[5] must be behind the heads. Suitably tension the belt [8].
- Fix the case to the upper guide of the door as shown in
fig. 7 or in fig. 9 .
3.2 Door wing fastening
- Place the door wing in the closure position.
- Position the door wing connection bracket [7] as close as
possible to the pulley and fix it to the door wing as shown
in fig. 7-9.
Attention: if the thickness of the door is different from 40 mm,
use suitable spacers that are not supplied.
Attention: the door wing connection brackets for double door auto-
mations must be positioned flush with the door as shown in fig. 5.
- Open and close the door to ensure that the door wing is
sliding correctly.
Attention: open the door wing completely and check that the
connection bracket [7] does not hit against the pulley.
3.3 Close stop fastening
For correct working, it is necessary to stop the sliding door wing
about 90mm before it reaches the fully opened position.
Fasten the close stop bracket (supplied) as shown in fig.11.
- The close stop bracket can be fastened on the inner or ou-
ter side of the door. Choose the most suitable position.
- Close the door completely and fasten the close stop bracket
using the slots, without tightening the screws.
- Open the door as far as the stop, leaving ~90mm within
the doorway.
- Close the door completely, tighten the screws, and perma-
nently fasten the close stop bracket using a third screw on
the non-slotted hole.
3.4 Fastening of the radio receiver
It is possible to install the radio receiver that allows the door to
be activated by means of wireless commands.
- Fasten the radio receiver [10] inside the box by means of
the supplied screws.
- Carry out the electrical connections as shown in the related
manual.
- Memorise the transmitters as shown in the related manual.
1. TECHNICAL DETAILS
Power supply
230 V~ / 50-60 Hz
Absorption 0.2 A
Accessories power supply 24 V= / 0.3 A
Thrust
30 N
Opening speed
Closing speed 0.4 m/s
0.2 m/s
Intermittence S2 = 30 min
S3 = 50%
Max load
40 kg
Dimensions
Max run
Temperature
-20 °C / +55 °C
Degree of protection IP20
115 x 67 x 1000 [940.41.043]
115 x 67 x 2000 [940.41.044]
910 mm [940.41.043]
1860 mm [940.41.044]
EN