Häfele 633.03.298 Скачать руководство пользователя страница 14

732.26.671

732.26.671

HDE KE1 16.12.2022

HDE KE1 16.12.2022

14

[1639723]

[1639723]

1.  Contents and target group of these instructions

These operating instructions must be followed in order to operate the control unit and the lifting 

device correctly and safely. 
The operating instructions must be read by the named groups of persons before they handle the 

lifting device or the control unit.

Instruction part

applies for

Operating instructions

Operators, qualified personnel (e.g. joiners, cabinet 

makers, furniture makers)

2.  General safety instructions

2.1  Meaning of the safety notes

The safety notes in these operating instructions are classified in accordance with the severity of 

the danger.

Warning

This safety note marks a potentially hazardous situation that could lead to severe inju-

ries.

Note

Notes are used to point out the possibility of consequential damage to the product if they 

are not complied with. Notes are also used to provide important additional information.

2.2  Safety notes

Note

he following safety note must be observed during the operation, in order to pre-

vent hazards.

General safety notes for operation

 

>

The control unit may only be fitted by qualified personnel. 

 

>

It must be possible to perform a reset at any time. There must not be any structural 

obstacles that hinder a reset.

 

>

Children may only use the control unit or the lifting device under the supervision of an 

adult.

 

>

Do not attach any additional objects or support yourself on the lifting device.

 

>

Immediately disconnect the power plug from the lifting device and contact the man-

ufacturer in the event of damage, smoke development or the occurrence of unusual 

noises/odours.

 

>

Do not install any heat sources in the vicinity of the lifting device (candles, heaters, 

etc.).

Electrical safety

 

>

Do not allow liquids to flow into the control unit (e.g. by knocking over containers filled 

with liquid on the worktop). 

 

>

Do not open the housing of the control unit.

 

>

Do not interconnect any distributor boxes or adapters. 

 

>

Never replace or modify the power plugs / mains leads.

ins-src-732.26.671.indb   14

16.12.2022   11:37:32

Содержание 633.03.298

























Отзывы: