background image

 

 

 

 

 

 

5.52.693.00.01.00 

 

  Do not use a hoist that is defective, pay attention to any abnormal noise it makes during operation. 

  Stop working immediately in case of disturbances and remedy failures. 

  Any damage and faults must be reported to a responsible supervisor immediately. 

  If the unit is put into motion, any persons in the immediate vicinity must be informed by calling to them! 

  Please pay attention to the regulations for load carrying devices UVV for both positive and non-positive 

methods of attaching loads. 

 

  The  lifting tackle or the  load  must  be securely attached  to the  hook  and be seated at the bottom of the 

hook. 

  The safety catch of hooks must be closed. 

  When charged, the housing may not be in contact somewhere. 

 

 

Transport and Storage 

 

   

CAUTION!

 

Transport  may  only  be  done  by  qualified  personnel.  No  liability  for  any  damage  resulting  from  improper 
transport or improper storage. 

 

3.1 

Transport 

 The devices are checked and if so adequately packed before delivery. 

  Do not throw or drop the equipment.  

  Use adequate means of transport. 

Transport and means of transport must be suitable for the local conditions. 

3.2 

Safety device for transport 

 

NOTICE!

 

Should a safety device for transport exist, please remove it before commissioning. 

3.3 

Storage 

  Store the equipment at a clean and dry place. 

  Protect the equipment against dirt, humidity and damage by an appropriate cover. 

  Protect hooks, wire ropes, chains and brakes against corrosion. 

 

Description  

 

 

 

4.1 

Areas of application 

The devices must be as far as possible installed in a covered room. 

If they are used in the open, protect the units against the effects of weather such as rain, hail, snow, direct 
sunshine,  dust,  etc.  -  we  recommend  to  use  a  cover  in  parking  position.  If  the  device  is  set  up  in  a 
continuously  humid  environment  with  strong  temperature  fluctuations,  the  correct  functionings  are 
endangered by the forming of condensation. 

NOTICE!

 

Use only in the intended atmosphere with a humidity of up to 100%, but not under water! 

 

 

During longer periods of standstill, corrosion may reduce the function of the brake. 

 

 

   

DANGER!

 

It is not permitted to use the unit in an area at risk from explosion!

 

 

 

 

Содержание 32/20

















Отзывы: