Hach ORBISPHERE K-M1100 Скачать руководство пользователя страница 103 | Manualshive

Страница: 103 / 116

background image

102

Maintenance and Troubleshooting

15.2.3 Sensor spot replacement

3.

When unscrewed completely simply lift out the old
sensor spot. Pull off the maintenance tool and
discard the old sensor spot.

4.

Check the red O-ring (position indicated right). If it
appears damaged in any way, then using a pair of
tweezers, remove and replace it with the new
O-ring from the maintenance kit.

N O T I C E

Avoid scratching or damaging the sensor spot (the
black surface on the sensor head) during this process.

1.

Push the maintenance tool (square sides upmost)
as far down as possible over the new sensor spot.
Continue to push down on the tool and turn gently
until the square sides of the tool and the square
slots of the sensor spot engage. The tool should
then drop into position.

2.

Make sure the sensor collar is as far down as it will
go, so that the top of the collar is aligned with the
base of the sensor head.

3.

Take the combined maintenance tool and sensor
spot and place it in the end of the sensor.

«
...
101
102
103
104
105
...
»

Содержание ORBISPHERE K-M1100





















































































































Отзывы:

Нет отзывов

Похожие инструкции для ORBISPHERE K-M1100

Бренд: Garland Страницы: 36

Бренд: 4MOMS Страницы: 20

Бренд: X-pole Страницы: 16

DWSC - Vintage C

Бренд: Daikin Страницы: 57

Wormhole Station JUH-320

Бренд: J5create Страницы: 24

NNC994S - Genius Prestige - Convection Microwave...

Бренд: Panasonic Страницы: 1

FRONT HEADLIGHT LENS COVER

Бренд: Bimmer Jakes Страницы: 4

DS-KABD8003-RS3

Бренд: HIKVISION Страницы: 3

Бренд: Alpine Страницы: 69

Бренд: Allen Sports Страницы: 2

Бренд: Berkefeld Страницы: 12

IR 2.0 12-24Vdc

Бренд: DOMUS LINE Страницы: 9

Бренд: Dometic GROUP Страницы: 20

STRONGARM RVR303

Бренд: Blue Giant Страницы: 48

Бренд: Becker Страницы: 52

Бренд: Kubota Страницы: 11

RideAlong Lite 100109

Бренд: Thule Страницы: 12

Бренд: ECS Electronics Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды