Hach ORBISPHERE K-M1100 Скачать руководство пользователя страница 102 | Manualshive

Страница: 102 / 116

background image

101

Section 15 Maintenance and Troubleshooting

15.1 Instrument maintenance

15.2 Sensor maintenance

The sensor spot needs to be replaced about once a year. It is recommended to calibrate the
sensor every 6 months for beverage applications with multiple CIP. The procedure is very
simple and takes no more than a couple of minutes. Based on the measurement range of
oxygen, the sensor lifetime can be shorter and the maintenance—and calibration—frequency
increased. If there are bleaching compounds and strong oxidants (e.g., ClO

2

) in the sample, the

sensor lifetime can also be shorter.

Important Note:

The shelf-life of the K1100/M1100 LDO spot is 2 years prior to first use.

15.2.1 Equipment required

15.2.2 Sensor spot removal

C A U T I O N

Personal Injury Hazard. Any instrument maintenance should be carried out by a qualified
Hach Service Technician. Please contact your local representative should you feel any
maintenance or instrument adjustments are required

A replacement sensor spot (No.

1

) and O-ring

(No.

3

) supplied with the sensor spot.

The maintenance tool (No.

2

) which is

delivered with the sensor.

1.

Push the maintenance tool (square sides upmost)
as far down as possible over the old sensor spot.
Continue to push down on the tool and turn gently
until the square sides of the tool and the square
slots of the sensor spot engage. The tool should
then drop into position.

2.

Turn the tool counter clockwise to unscrew the old
sensor spot.

«
...
100
101
102
103
104
...
»

Содержание ORBISPHERE K-M1100





















































































































Отзывы:

Нет отзывов

Похожие инструкции для ORBISPHERE K-M1100

Бренд: Oki Страницы: 2

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 10

Бренд: Panasonic Страницы: 14

Бренд: Panasonic Страницы: 30

Бренд: IHP Страницы: 8

Бренд: Back View Страницы: 168

Бренд: Caberg Страницы: 3

Бренд: Caberg Страницы: 2

Бренд: Dacor Страницы: 4

Бренд: Obelink Страницы: 2

Бренд: Jeda Страницы: 8

Бренд: Tait Страницы: 10

Powersaver Dual Flexi

Бренд: Sangamo Страницы: 2

Бренд: Vaillant Страницы: 80

WORKCENTRE C2424

Бренд: Xerox Страницы: 2

Бренд: Mobis Страницы: 16

Бренд: Mightymast Leisure Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды